GIA GIA-PB-09P16 Owner'S Manual Download Page 11

 

  

11 

Trouble Shooting 

Please contact professional serviceman without delay in following situation 

Trouble 

Cause 

Solution 

Machine cannot   

work 

Power off 

Power on 

water-full indicator turns on 

Drain water out 

 

 

Machine 

auto-restarts 

frequently 

Direct sunlight 

Draw the curtains 

Door and windows are open, 
many heat sources in the room. 

Close the door and windows, move out 
heat sources. 

Filters are too dirty. 

Clean or replace filters 

Air-inlet or air out-let is blocked 

Remove blockage 

Too noisy 

Machine is not put on flat ground. 

Place it on flat and solid ground, avoiding 

shaking 

Compressor 

cannot work 

Compressor time-delay 
protection turns on 

Wait for 3 minutes, then restart the 
machine after temperature reduces. 

Note: when abnormal situations are occurred, turn off machine and pull out plug,   

then contact with professional electrician for help. 

 

 

 

 

THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE PART OF 

FINAL USERS IN THE EUROPEAN UNION” 

 

This symbol on the product or on the container indicates that this product cannot be eliminated 
with the general waste. The user is responsible for eliminating this kind of waste by throwing 
them away at a “recycling point” specifically for electrical  and electronic waste. Selective 
collection and electrical equipment recycling contribute to preserve natural resources and 
warrant waste recycling to protect environment and health. In order to receive further 
information about electrical and electronic waste collecting and recycling, contact your Local 
Council, the service of household waste or the establishment where the product was acquired.

 

Summary of Contents for GIA-PB-09P16













Reviews: