Ghost Controls TSS1 Installation And Owner'S Manual Download Page 56

Page: 56 / 64

2 0 2 0

POWERING THE SYSTEM WITH SOLAR

STEP 19.

Adding a solar panel (optional) to the control box.

When wiring a Solar Panel you will need to remove the plug in the negative solar terminal on the main con-

trol board and then connect the solar panel wires to the matching terminals 1 and 3 on the SOLAR PWR

INPUT screw terminal on the control board. Please refer to diagram below.

DO NOT CONNECT AC

TRANSFORMER IF USING SOLAR POWER.

DO NOT USE this terminal

if using Solar Panel

Black

Red

Battery Harness

Operator Arm

Check that green LED (Power status) on top center of control board is on. This indicates that the battery is

being charged.

Check the chart shown for number of hours of direct sunlight available for solar applications.

Determine the number of expected winter cycles for a single gate using solar power by reviewing the map and

chart shown.

SHOULD BE CONNECTED TO ANY GHOST CONTROLS SYSTEM CONTROL BOARD.

Summary of Contents for TSS1

































































Search results

Summary of Contents for TSS1

Reviews:

Related manuals for TSS1

Brands by name

Popular brands

Ghost Controls TSS1, Installation And Owner'S Manual

Search results

Summary of Contents for TSS1

Reviews:

Related manuals for TSS1

Brands by name

Popular brands