manualshive.com logo in svg

GHM GREISINGER GFTH 200 Kal, Operating Manual, Page: 26 / 32

Share
Download
GHM GREISINGER GFTH 200 Kal Operating Manual Download Page 26

8 | Error and system messages

GMH 3331

26 / 32

B-H77.0.01.DB2-1.0

8 Error and system messages

Display

Meaning

Possible

 

causes

Remedy

SENS ERRO

No probe or sensor
connected

Sensor or probe de-
fect

Measuring range ex-
ceeded or undercut

Sensor or probe
missing

Defective sensor or
probe

Incorrect sensor
type selected

Connect sensor or probe

Connect different sensor or
probe

Readjust measuring range

No display,
unclear char-
acters or no
response
when but-
tons are
pressed

Battery depleted

System error

Product is defective

Battery depleted

Error in the product

Product is defective

Replace battery

Send in for repair

BAT

 blinks

Battery low

Battery low

Replace battery

BAT

Battery depleted

Battery depleted

Replace battery

(AL ERR.1

Zero point calibra-
tion defective

ERR.1

Measuring range ex-
ceeded

Measurement too
high

Measuring probe,
sensor or product
defect

The measurement is above
the permissible range

Test measuring probe or
sensor

Send in for repair

ERR.2

Measuring range is
undercut

Measurement too
low

Measuring probe,
sensor or product
defect

The measurement is below
the permissible range

Test measuring probe or
sensor

Send in for repair

ERR.3

Display range has
been exceeded

Value is too high

Adjust measuring range

ERR.4

Display range has
been undercut

Value is too low

Adjust measuring range

ERR.7

System error

Error in the product

Switch the product on/off

Replace batteries

Send in for repair

ERR.9

Sensor/probe not
available

Sensor/probe error

Sensor/probe not
connected

Sensor/probe defect

Switch the product on/off

Connect sensor/probe

New sensor/probe

ERR.11

Measurement value
could not be calcu-
lated

Measurement vari-
able not available

Incorrect unit setting

Change/adjust measure-
ment variable

Enter suitable unit

Summary of Contents for GREISINGER GFTH 200 Kal

































Reviews:

No comments