background image

 

  

15 

 

10

 

Declaration of incorporation / conformance 

Declaration of incorporation

  

in the terms of Machinery Directive 2006/42/EC 
for partly completed machinery, Appendix II Part B

 

 

 

 

Declaration of conformity 

in terms of EMC Directive 2014/30/EU

 

We, the 

GfA ELEKTROMATEN GmbH & Co. KG 

hereby declare that the following products are conform with the above  

EC Guideline and are only intended for installation in door equipment. 

SE 7.32 WS-25,40 

Standards applied 
DIN EN 12453 
DIN EN 12604 
DIN EN 60335-1 
 
DIN EN 61000-6-2 
 
DIN EN 61000-6-3 

 
Doors - safety in use of power operated doors 
Doors - Mechanical aspect 
Safety of household and similar electrical appliances  
Purposes - Part 1 : General requirements 
Electromagnetic compatibility (EMC) Part 6-2  
Generic standard – Immunity standard for industrial environments 
Electromagnetic compatibility (EMC) Part 6-3  
Generic standard – Emission standard for residential,  
commercial and light-industrial environments 

We undertake to transmit in response to a reasoned request by the appropriate regulatory 

authorities the special documents on the partly completed machinery. 

Authorised representative for the compilation of the relevant technical documents 

(internal EU address) 

Dipl.-Ing. Bernd Synowsky 

Documentation representative 

Incomplete machines within the meaning of the EC Directive 2006/42/EC shall only be intended to 

be integrated into other machines (or into other incomplete machines/systems) or to be assembled 

with them to form a complete machine within the sense of the Directive. Therefore, this product 
cannot be commissioned before it is determined that the entire machine/system to which it was 

integrated shall comply with the provisions of the Machinery Directive indicated above. 

Düsseldorf, 24.11.2015

 

Stephan Kleine 

 

 

CEO

 

Signature 

 

 

Summary of Contents for ELEKTROMAT SE 7.32 WS-25,40

















Reviews: