background image

14

GF U3000 V2 Ultrasonic Flowmeter

Modbus Supplement to the operating instructions

3.9 

Status Flags

Various status flags that have not been discussed earlier, are outlined in the register map in Figure  above, but are also shown below 
along with a more verbose description of their use.

Element

Bit name

Description

Instrument Control Flags

Lock screen mode

This is a Read/Write bit. When read, it indicates whether the Lock Screen 
Mode on the unit is on (=1) or off (=0). To change the Lock Screen Mode, follow 
the procedure outline in 2.6.2 but substitute step 3 and 4, first with a MASK 
WRITE REGISTER message (command 22 or 0x16) to register address 6 
(address 5) and the OR set as appropriate to set to Lock screen Mode. This is 
followed by another MASK WRITE REGISTER message (command 22 or 0x16) 
to register address 6 (address 5) with the AND mask being set to 0xFFFB and 
the OR mask being 0x0004. This will initiate an “Update Lock Screen Mode” 
command on the unit.

Instrument General 
Flags

Screen lock mode active This flag indicates that the unit is reading flow, lock screen mode is enabled, 

and the keyboard is locked against local entry for the moment.

Status Flags

Online

The unit is currently reading flow. This flag is reset when the unit stops 
reading flow and enters the configuration mode.

Status Flags

Urgent Error

An urgent error has been reported. This can be useful to indicate that a 
serious error has occurred in the unit. For a list of urgent errors see the GF 
U3000 V2 Ultrasonic Flowmeter manual.

Status Flags

Remote Total Changes 
Disabled

A local operator has temporarily barred the MBM from changing the flow 
totals.

Status Flags

Current Loop Alarm

An alarm condition has been set on the current-loop and the conditions that 
trigger it has been met.

Status Flags

Digital Device 0 .. 3

N.B. Digital device 0 is currently unimplemented, and so will always read 
zero. Digital device 1..3 correspond to output 1..3. If a flag is set then this 
output has been configured as an alarm, and the alarm condition has been 
met.

Status Flags

Hot / Cold probe fault

The hot or cold probe is faulty or has been disconnected. The temperature 
associated with a faulty or disconnected probe will -259.3 °C

Status Flags

Signal Loss

The ultrasonic signal has been lost. Flow and volume readings will be frozen.

GLOSSARY

Below is a list of abbreviations and their meaning:

Abbreviation

Meaning

MBM

Modbus Master

SP

Single Precision

DP

Double Precision

REG

Register

IDX

Index

Summary of Contents for U3000 V2

















Reviews: