background image

7

About this manual

Gewiss

1.  About this manual

The purpose of this manual is to describe the JOINON electric vehicle charging stations and to provide appropriate 
information for their correct reception, installation, start-up, maintenance and operation.

1.1.  Scope of application

This manual is valid for the following charging stations:

JOINON Home

JOINON Home GW68101 (single phase)

JOINON Home GW68102 (three phase)

JOINON Home GW68101R (single phase)

JOINON Home GW68102R (three phase)

JOINON Parking

JOINON Parking GW68103 (single phase)

JOINON Parking GW68103R (single phase)

JOINON Parking GW68104C (three phase)

1.2.  Recipients

This document is intended for qualified personnel. 

The status of qualified personnel referred to in this manual will be, as a minimum, that which meets all the 
standards, regulations and laws regarding safety applicable to the tasks of installing and operating this unit.

It is recommended that this unit is installed by a professional installer.

1.3.  Symbols

This manual uses various symbols to emphasize and highlight certain texts. The general meanings are explained 
below.

General warning.

General information.

Electrical danger.

Read the section indicated.

Prohibition.

ABA2023IQM01_ - 7.55.4.412.2 - Installation and Operation Manual

EN

ES
FR
IT
HU

ABA2023IQM01_ - 7.55.4.494.0

ABA2023IQM01_ - 7.55.4.494.0

Summary of Contents for JOINON Home GW68101









































Reviews: