background image

 

 

 

   

15 

Operating data 

Retention force 

350–1,100 N 

  

Compressed air supply of VZ 10 

Minimum 

4.5 bar 

Maximum 

9 bar 

  

Proximity switch (Pepperl & Fuchs) characteristics, VZ 10 

Type 

NJ 10-30 GK-N 

NJ 10-30 GK-SN  NJ 5-30 GK-S1N 

Rated voltage [V] 

8.2 

Power consumption [mA] 
Active surface not covered 

≥ 3 

≥ 3 

≤ 1 

Active surface covered 

≤ 1 

≤ 1 

≥ 3 

Admissible ambient temperature [°C] 

–25 / +100 

–50 / +100 

–25 / +100 

IP rating 

IP66/IP68 

IP68 

IP68 

  

Pressure & temperature ratings 

You can find the values for your equipment on the 
rating plate. 

  

Manufacturer's declaration 

For more information on the Conformity 
Assessment according to European rules refer to 
our Declaration of Conformity or our Declaration by 
Manufacturer. 
To download the current Declaration of Conformity 
or Declaration by Manufacturer go to 
www.gestra.com/documents or contact: 

  

GESTRA AG 

Münchener Straße 77 
28215 Bremen 
Germany 
Telefon 

+49 421 3503-0 

Telefax 

+49 421 3503-393 

E-Mail 

[email protected] 

Web 

www.gestra.de 

  

 

  

This declaration is no longer valid if modifications 
are made to the equipment without consultation 
with us. 

  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

  

 

  

Summary of Contents for VZ 10

















Reviews: