GeoSlam K GS ZEB VISION Hardware User'S Manual Download Page 2

 

 

© 2022 GeoSLAM Ltd                                                  1                                     ZEB Vision User Guide v1.3 

 

 

Notes 
 

The software and hardware described in this guide is furnished under licence and may only be used or copied 
in accordance with the terms of the licence.

  

Copyright © GeoSLAM Ltd. 2022

  

Revision: 1.3 
Release date: 30 May 2022

 

  

All rights are reserved.  No part of this publication or the components it describes may be reproduced, stored in 
a retrieval system or transmitted, in any form, or by any means, electronic, mechanical, photocopying, recording, 
or otherwise, without prior written consent from GeoSLAM Ltd.

  

  

GeoSLAM 

Ltd.  provides  this  guide  “as  is”,  without  warranty  of  any  kind  and  reserves  the  right  to  make 

improvements and/or changes to the product described in this guide at any time and without notice.

  

 

GeoSLAM Ltd. equipment should not be used as a primary navigation device.

  

  

CLASS A COMPUTING DEVICE

.  This equipment has been tested and found to comply with the limits for a 

Class A digital device, pursuant to Part 15 of the FCC rules.  These limits are designed to provide reasonable 
protection  against  harmful  interference  when  the  equipment  is  operated  in  a  commercial  environment.  The 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance 
with the user guide, may cause harmful interference to radio communications.  Operation of this equipment in a 
residential  area  is  likely  to  cause  harmful  interference,  in  which  case  the  user  will  be  required  to  correct the 
interference at their own expense.  
  

SOFTWARE IS PROVIDED AS IS.

  To the maximum extent permitted by law, the manufacturer (GeoSLAM Ltd.) 

and its suppliers disclaim all warranties, either express or implied, including, but not limited to implied warranties 
of merchantability and fitness for a particular purpose, with regard to the SOFTWARE, the accompanying written 
materials, and any accompanying hardware.  You may have other rights which vary from country to country.  
  

NO LIABILITY FOR CONSEQUENTIAL DAMAGES.

  To the maximum extent permitted by applicable law, in 

no event shall the company or its suppliers be liable for any damages whatsoever (including without limitation, 
direct or indirect damages for personal injury, loss of business profits, business interruption, loss of business 
information, or any other pecuniary loss) arising out of the use of this product, even if the company has been 
advised of the possibility of such damage

s. In any case, the company’s and its suppliers’ entire liability shall be 

limited  to  the  amount  actually  paid  by  the  owner  of  the  product  for  the  product.  Because  some 
states/jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages, 
the above limitation may not apply to the user. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for K GS ZEB VISION












Reviews: