geo-FENNEL FET 420K Operator'S Manual Download Page 23

Page: 23 / 32

ERROR DISPLAY

DISPLAY

ERROR CONTENT AND DISPOSAL

Vertical compensator out of compensating range.
Level the instrument again

E00

Collimate rotating too fast. Press 0SET key to set 0.
If “

E00”

is shown again instrument needs to be repaired.

E01

Telescope turning too fast, press V/% key to set 0 for the vertical
plate specification.

E02

Interior error of the horizontal angle measuring system. Power on
the instrument again. If error is shown again instrument needs to be
repaired.

E03

Interior error of the vertical angle measuring system.
If error is shown again instrument needs to be repaired.

E04

Difference between every value exceeds 30? during the angle
repeated measurement, press 0SET key and measure repeatedly.

E05

Times of angle repeated measurement exceed 15, press key and
measure repeatedly.

E06

Errors during the process of the vertical angle 0set or adjusting 0set
when the clamp angle to the horizon exceeds 45°. Need adjusting
repeatedly.

Attention:

Check fully every part of the instrument and see whether the operation coincide with
the procedures after the error appears.
If the error code is still shown after many checks please send the instrument for
repair.

Summary of Contents for FET 420K

































Search results

Summary of Contents for FET 420K

Reviews:

Related manuals for FET 420K

Brands by name

Popular brands

geo-FENNEL FET 420K, Operator'S Manual

Search results

Summary of Contents for FET 420K

Reviews:

Related manuals for FET 420K

Brands by name

Popular brands