background image

 

 

 

Date                ,        ,

 

VIN

Approv

ed

 

 

 

 

 

Checked

 

 

Person i

n

 

 

charg

e

 

 

 

INSTALLATION 

INSPECTION 

SHEET

 

MAZDA 

CX-9 

Car-navigation unit

 

TKY2 79 EZX (US/CANADA) 

TKY3 79 EZX (MEXICO)

 

 

Perform the following inspections

 

 

1. Inspection items after installation

 

 

x

 

Verify the fitting between the vehicle part and the installed part, and inspect for damage or 
dirt.

 

 

x

  When connecting connectors, verify the connection again to prevent poor connection or 

mis-connection. (Insert two times.)

 

 

2. Vehicle parts reinstallation

 

Inspected part 

Inspection 

item 

Inspection Check

 

Negative battery terminal 

Torque 
change 

Is the nut for the negative battery terminal tightened to 
the specified torque? 

Tightening torque: 2.9

4.9

 

N

m

 

 

Power window switch panel 

Operation 

Verify the operation of all power windows which were 
removed and installed. Verify the automatic operation 
of the driver’s window. 

 

 

3. Installation of accessory, operation check

 

Inspected part 

Inspection 

item 

Inspection Check

 

Car-navigation unit

 

Check 

Was “5. Operation check” performed?

 

 

 
 
 
 
 
 
 
 
 

 

 

Check 

The term of validity for this sheet : 3 year

 

 

Check 

Summary of Contents for TKY2 79 EZX













Reviews: