Genuine Scooter Company Buddy 170 Service Manual Download Page 58

Page: 58 / 137

5.To assemble the driving pulley, reverse the whole procdeure.

Locking torque:

1.Nut of driving pulley M10:4.0-5.5kg/m.

2.Locking nut of clutch M10:4.0-5.5kg/m

6.Checking driving belt

(1)check driving belt is cracked or not

rubber and fiber is loosened or not

also check if they are extraordinary

worn out.

(2)driving belt width:

change it below using limit

7.Disassemble slide driving plate set.

(1)Remove bush of slide driving plate.

(2)Remove screw, and disassemble the

cover of slide driving plate.

(3)Remove ramp plate.

(4)Remove weight roller.

8.Checlomg

(1)Check the wearing condition of

weight roller.

change it below when below using limit

Summary of Contents for Buddy 170










































































































































Search results

Summary of Contents for Buddy 170

Reviews:

Related manuals for Buddy 170

Brands by name

Popular brands

Genuine Scooter Company Buddy 170, Service Manual

Search results

Summary of Contents for Buddy 170

Reviews:

Related manuals for Buddy 170

Brands by name

Popular brands