Genuine Scooter Company Buddy 170 Service Manual Download Page 51

Page: 51 / 137

D.Dismantling the step plates and lower

Mudguard:

1.Take off the screws of the four

step plates and take off the four

step plates.

2.Screwing out the screws of lower

mudguard.

E.Dismantling the step floor and front

inner cover:

1.screwing out the screws of battery

cover.

2.Disconnect the negative, then

positive cable.

3.Screwing out the screws between the

step floor and front inner cover

Take off the front inner cover.

4.Pull out both the negative and

Positive battery cables, Take off

The step floor.

5.When assembling, the procedures

Will be reversed.

M6:0.7-1.1kgf-m

M5:0.35-0.5kgf-m

Note:Avoid clamping and scraping the

Cables or pipes by the plastic parts.

Summary of Contents for Buddy 170










































































































































Search results

Summary of Contents for Buddy 170

Reviews:

Related manuals for Buddy 170

Brands by name

Popular brands

Genuine Scooter Company Buddy 170, Service Manual

Search results

Summary of Contents for Buddy 170

Reviews:

Related manuals for Buddy 170

Brands by name

Popular brands