background image

ENGLISH

Genius Car Alarm

www.geniuscaralarm.com

27

 

 

1. Press 

button  1

,  then press 

button  3 

within two seconds, the ultrasonic  sensor is 

cancelled.  

2. Press 

button 1

, then press 

button 2

 within 2 seconds, both the ultrasonic sensor and 

the door’s signal are cancelled.  

DOORS’ SIGNAL ARMING DELAY  

This function allows us to arm the alarm even when the dome lights are on, because the 

system will not recognize this signal for the programmed time, avoiding notices of open 

door when the alarm is armed.  

* See Programming Table-

 

 

Disarm of the system using the reset button 

In case you lose the transmitter, damage it or the battery of the same dies, 

you can disarm the system by pressing the reset button. 

First, with the security system armed, open the driver’s door and the siren will 

start sounding. 

Second, turn ON the ignition switch, before the 10 seconds press the reset 

button the number of times assigned in the security code (1 as set by the 

factory) the siren will continue to sound for 3 seconds and if the security code 

is right the system will disarm. 

PANIC 

With this function, we can make the system to trigger intentionally to prevent or attract the 

attention of people, in case of a theft or aggression attempt.   

 

a. With the ignition in OFF,  

   - PANIC, 

BUTTON 3

 FOR 3 SECONDS 

b. The siren and the lights will trigger for 3 seconds. 

c. Press 

button 1

 or 

button

 

2

 to stop PANIC, the system will remain armed.  

d. With the ignition in 

ON. 

Activate PANIC. 

By stopping PANIC, the system will remain armed without the ignition interrupter, but if the 

ignition key is turned to OFF position, the IGNITION INTERRUPTER will be activated.  

 

CAR FINDER 

With this function we can make the system to send us signals with the siren and lights, 

which will serve us to locate the vehicle, whenever we are in the transmission range 

between the remote control and the vehicle.  

 

a. When the alarm is armed,  

- CAR FINDER, 

BUTTON 

1 FOR 1 SECOND  

b. The siren will chirp 10 times and the parking lights will flash 10 times.  

c. Press 

button 1 

or 

button 2

 to stop the Car Finder.  

 

ANTI-HIJACKING BY IGNITION (Programmable by Jumper)  

This function is in the memory’s software to activate automatically the anti-hijacking mode 

every time the ignition key is turned form OFF position to ON position. (See Jumpers table) 

 

ANTI-HIJACKING BY TRANSMITTER (Programmable)  

This function is used to immobilize the vehicle in case of emergency, pressing the buttons 

1 and 2 simultaneously for 3 seconds and the anti-hijacking mode will activated by 

transmitter. (See Functions Programming Table)  

 

 

Summary of Contents for G24AU1B
















Reviews: