ITA
DESCRIZIONE
SPECIFICHE TECNICHE
·
Batteria 3 V (cr2450)
·
Frequenza di trasmissione: 433 MHz
·
Potenza di trasmissione: 10 mW
·
Temperatura di esercizio: -10°C ÷50°C
·
Distanza di trasmissione: 200m in uno spazio
aperto, 35m con due pareti
ISTRUZIONI DI D’USO
Attenzione: per garantire una durata prolungata del trasmettitore,
non esporlo a umidità o urti.
Utilizzando il trasmettitore, se si rileva una distanza di emissione
troppo breve o se la sensibilità del dispositivo diminuisce, sostituire
le batterie. Smaltire correttamente le batterie usate.
CAMBIAMENTO DELLA MODALITÀ DI FUNZIONAMENTO
IMPOSTAZIONE DELL’ORA CORRENTE
(SOLO IN MODALITÀ MANUALE)
Radiocomando monocanale con programmazione oraria
CRH-01-T-00
Pulsante Su
Pulsante Stop
Pulsante Giù
Retro
Pulsanti
ausiliari P1-
Pulsanti
ausiliari P1+
Pulsante
Impostazione ora
Pulsante di
impostazione
Pulsante
Modalità
Ora
manuale,
auto,
random
Carica
Batteria
Sù
Minuti
Giù
Settimana
Modalità manuale:
trasmettitore normale,
senza funzione di
impostazione dell’ora
Modalità automatica:
trasmettitore normale,
con funzione di
impostazione dell’ora
Modalità casuale: trasmettitore
normale con funzione di impostazione
dell’ora, emissione casuale in un
periodo di tempo di 15 minuti
Premere più volte il “pulsante
Modalità” per scorrere ciclicamente
tra le tre modalità “Manuale –
Automatica – Casuale”
Durante il processo di impostazione dell’ora, sono disponibili
60 secondi per premere ciascun pulsante; il dispositivo esce
automaticamente dalla modalità di impostazione dopo 60 secondi se
nessun pulsante verrà premuto.
Premere il pulsante
“Modalità” per
passare alla
modalità manuale
Premere il pulsante
“Impostazione ora”
per 3 secondi, finché
la parola “ora” non
inizia a lampeggiare
Premere i pulsanti
“Su” oppure “Giù”
per impostare l’ora
Per impostare i minuti,
premere “P1+” finché
la parola “minuto” non
inizia a lampeggiare
Premere i pulsanti
“Su” oppure “Giù” per
impostare i minuti
Premere “P1+” finché la
parola “settimana” non
inizia a lampeggiare
Premere i pulsanti
“Su” oppure “Giù” per
impostare la settimana
Tenere premuto il pulsante “Impostazione
ora” per 3 s.; le cifre corrispondenti ai
campi “ora” e “minuto” lampeggeranno
contemporaneamente. Salvare l’impostazione
Premere il pulsante
“Impostazione ora”; i secondi
verranno riportati a zero e
inizierà il conteggio del tempo
or
or
or
CHECKING AND SETTING THE SET TIME (NON-GROUP CONTROL)
MATCHING AND SETTING UP TUBULAR MOTOR
ENG
Single channel remote control with hourly programming
CRH-01-T-00
1. In the process of setting, you
have 60 seconds to press each
button; setting mode will quit
automatically after 60 seconds
if no button is pressed.
2. The time interval between
the motor going up and down
must be over 32 mins. If it is
less than 32 mins, it will show
“Er01”to remind you that the
operation is wrong, and you
need to reset it.
3. In Timer Setting status, press
the P1-/P1+ button on the
channel briefly to set Minutes/
Hours.
4. In Timer Setting status, press
the Mode button briefly to set
Timer Up/Down.
5. While viewing and setting the
status, you can press the stop
button to exit immediately.
6. When you have finished setting
timing, it will be memorized
even during a blackout.
……
Press the “Mode”
button to switch to
auto or random mode
Press the “time setting” button
and hold for 3s to enter timing
status; press the up or down
button to check the set time for
every day
Press the “Time setting”
button ; the hour will
flash; enter the up time
setting status
Press the “Up” or “Down”
button to adjust the time
(hours)
Press “P1+” to adjust the
up time (minutes); minutes
will flash
Press the “Up” or
“Down” button to adjust
the time (minutes)
Press “Mode button”, which
confirms the set up time, and
switches to down time setting;
the hour will flash
Press the “Up” or “Down”
button to adjust the time
(hours)
Press “P1+” to adjust
the down time (minutes);
minutes will flash
Press the “Up” or
“Down” button to adjust
the time (minutes)
Press “Time Setting” button,
which confirms the set down time
After setting up and down timing for the whole week
in turn, press the “Time setting button” and hold for
3s; the “Hour” and “min” on the LCD will flash, and
then all the settings will be saved and the device will
automatically quit setting mode
or
or
or
or
or
The matching operations between emitter and tubular motor are detailed in each motor instructions.
During setting, the time between two operations must be shorter than 4s, otherwise the device will quit the setting program.
Motors powered by electrical grid either directly or through a power supply unit contain a buzzer.
A beep sounds to confirm each step in programming. When the power supply is applied, the buzzer emits a long sound
confirming connection.
Instead, each stage in programming of battery-operated motors is confirmed by motor turning briefly forward and back.
Power on
Beep once
(or motor turning
briefly forward
and back)
Set up is ok.
The Up button controls
the motor clockwise
Set up is ok.
The Down button
controls the motor
clockwise
Beep once
(or motor turning
briefly forward
and back)
P2x1
P2x1
UpX1
DownX1
OK
OK
Beep once
(or motor turning
briefly forward
and back)
Beep once
(or motor turning
briefly forward
and back)