BLIZZARD 500-900 C
6
532103 - Rev.B
Tr
ansla
tion of the original instruc
tions
ENGLISH
Tr
ansla
tion of the original instruc
tions
ENGLISH
3.1 INTENDED USE
GENIUS BLIZZARD 500-900 C series gear motors are designed to
operate horizontal sliding gates for residential use (including in
apartment complexes).
One gear motor must be installed for each sliding gate section. The
gate must be moved via a rack.
Installations of BLIZZARD 500-900 C must be used for vehicular traffic.
To operate the gate manually, follow the instructions in § 5.5.
!
Any other use which is not expressly specified in these instructions is
prohibited and could affect the integrity of the product and/or represent
a source of danger.
3.2 LIMITATIONS OF USE
The gate must fall within the dimensional and weight limitations
indicated in the technical data section. Obey the limitations on
frequency of use listed in the technical data section.
Using the product in any configuration other than that provided for
by FAAC S.p.A. is prohibited. It is prohibited to modify any product
component.
The presence of weather conditions such as snow, ice and strong
wind, even when occasional, could compromise correct automation,
affect the integrity of the components and represent a potential
source of danger.
If a pedestrian access gate is integrated in the sliding gate section,
motorised movement must be disabled when the pedestrian gate
is not closed.
BLIZZARD 500-900 C is not designed as a security (break-in protec-
tion) system.
Implementing automation requires the installation of the necessary
safety devices, identified by the installer through an appropriate risk
assessment of the installation site.
3.3 PROHIBITED USES
-
Uses other than the intended use are prohibited.
-
It is prohibited to install the automation system outside of the
limits specified in the Technical Data and Installation Require-
ments sections.
-
It is prohibited to install the automation system on escape routes.
2.3 UNPACKING AND HANDLING
RISKS
PERSONAL PROTECTIVE EQUIPMENT
1. Open the package.
The gear motor casing is not fixed.
2. Remove the magnetic limit switches and the bag of accessories.
3. Remove the casing.
!
Do not lift the gear motor by the electronic board.
4. Lift the gear motor, holding it by the base.
Check that all components are present and intact
2
.
5. Dispose of the packaging materials.
3. BLIZZARD 500-900 C
!
The packaging materials (plastic, polystyrene etc.) must not be left
within reach of children, as they are potential hazards.
When you have finished with them, dispose of the packaging in the
appropriate containers, as per applicable waste disposal regulations.
2.4 DISPOSAL OF THE PRODUCT
-
It is prohibited to install the automation system to create fire
doors.
-
It is prohibited to install the automation system in environments
which represent an explosion or fire hazard: the presence of
flammable gases or fumes represents a serious safety hazard
(the product is not 94/9/EC ATEX certified).
-
It is prohibited to power the system with energy sources other
than those specified.
-
It is prohibited to integrate commercial systems and/or equip-
ment other than those specified, or use them for purposes not
envisaged and authorised by the corresponding manufacturers.
-
It is prohibited to use and/or install accessories which have not
been specifically authorised by FAAC S.p.A.
-
It is prohibited to use the automation system before performing
commissioning.
-
It is prohibited to use the automation system in the presence of
faults which could compromise safety.
-
It is prohibited to use the automation system with the fixed and/
or mobile guards removed or altered.
-
Do not allow water jets of any type or size to come into direct
contact with the gear motor.
-
Do not expose the gear motor to corrosive chemical or atmos-
pheric agents.
-
Do not use the automation system unless the area of operation
is free of persons, animals or objects.
-
Do not remain in or walk/drive through the area of operation of
the automation system while it is moving.
-
Do not try to prevent the movement of the automation system.
-
Do not climb on, hold onto or let yourself be pulled by the
gate. Do not climb onto or sit on the gear motor.
-
Do not allow children to approach or play in the area of operation
of the automation system.
-
Do not allow the control devices to be used by anyone who is
not specifically authorised and trained to do so.
-
Do not allow the control devices to be used by children or persons
with mental and physical deficiencies unless they are supervised
by an adult who is responsible for their safety.
!
During manual operation, gently guide the gate the whole way, do not
push it and let it slide freely.
After dismantling the product, dispose of it in compliance with
Standards in force.
The constructive components and materials, batteries and electronic
components must not be disposed of with household waste but deli-
vered to authorised disposal and recycling facilities.
https://smartel.ua
