Genie X-135/70 Operator'S Manual Download Page 7

Page: 7 / 71

First Edition • Seventh Printing

Operator's Manual

Symbol and Hazard Pictorials Definitions

Part No. 160567

ZX-135/70 5

Platform tie-down
instructions

Lifting & tie down instructions

Tie-down point

Lifting point

Wind speed

Maximum capacity

Weight of welder
reduces capacity

Wheel load

Tire specifications

Do not use ether or
other high energy
starting aids on
machines equipped
with glow plugs.

Voltage rating for
power to platform

Pressure rating for air
line to platform

Color Coded
Direction Arrows

Runaway Hazard

Recovery procedure if tilt alarm sounds while
elevated.

Platform uphill:
1

Lower primary

Retract/lower
secondary

Retract primary

Platform downhill:
1

Retract primary

Retract / lower
secondary

Lower primary

Access by trained
and authorized
personnel only

Summary of Contents for X-135/70








































































Search results

Summary of Contents for X-135/70

Reviews:

Related manuals for X-135/70

Brands by name

Popular brands

Genie X-135/70, Operator'S Manual

Search results

Summary of Contents for X-135/70

Reviews:

Related manuals for X-135/70

Brands by name

Popular brands