background image

Third Edition • First Printing

 

Operator's Manual

 

 

Inspections 

 

 

Part No. 1298031GT

 

Super-Straddle 

17 

 

 

 

Do Not Operate Unless: 

 

You learn and practice the principles of safe 
machine operation contained in this operator’s 
manual. 

1  Avoid hazardous situations. 

2  Always perform a pre-operation inspection. 

3  Always perform function tests prior to use. 

4  Inspect the workplace.

 

Know and understand the workplace 
inspection before going on to the next 
section.

 

5  Only use the machine as it was intended. 

Workplace Inspection 
Fundamentals 

The workplace inspection helps the operator 
determine if the workplace is suitable for safe 
machine operation. It should be performed by the 
operator prior to moving the machine to the 
workplace. 

It is the operator’s responsibility to read and 
remember the workplace hazards, then watch for 
and avoid them while moving, setting up, and 
operating the machine. 

Workplace Inspection Checklist 

Be aware of and avoid the following hazardous 
situations: 

  drop-offs or holes 

  bumps, floor obstructions or debris 

  improper use on sloped surfaces 

  unstable or slippery surfaces 

  overhead obstructions and high voltage 

conductors 

  hazardous locations 

  inadequate surface support to withstand all 

load forces imposed by the machine 

  wind and weather conditions 

  the presence of unauthorized personnel 

  other possible unsafe conditions 

 

Summary of Contents for Super-Straddle




























Reviews: