Genie GCL-J&H Installation Manual Download Page 24

Page: 24 / 56

6.1

OPEN

STOP

CAL

RUN

SCROLL

SET

CLEAR

Section 6: Operator Setup Procedure

Operators include a full function control panel including a liquid crystal

display (LCD), calibration keys and Open, Close and Stop keys for on board

operator control. See

Fig. 1

. The open, close and stop keys function as a 3-button

wall control. The Display will show current operator conditions and calibration

information. Due to limited character space, some displays will be abbreviated.

See Appendix C (pgs. 10.9-10.11) for full display descriptions.
Operators include a non-volatile memory. The unit will remember all

calibration settings plus error code and run code logs, if power is removed from

unit.

DANGER:

After power is supplied to the operator,

Do Not

make

contact with components inside the control panel except for the Keypad

Keys.

Fig. 1

Control Operating Modes

Operator control boards operate in two modes: Run Mode and Calibration

Mode. The control board should normally operate in the Run Mode. The operator

is calibrated in Calibration Mode.

With the operator standing idle

PRESS CAL/RUN TO TOGGLE BETWEEN OPERATING MODES.

•

The first display in calibration mode is “SET CLOSE DIRECTION”

•

The display in run mode will be one of the condition codes listed

in Appendix C.

Control Panel

Operation Keys, operate

unit like a 3-button

wall station.

Scroll Keys, used in

Calibration Mode.

Set/Clear Key, used to

reset and adjust

calibration settings.

Figure 1

Calibration & Run

Mode Toggle Key.

Display Backlighting

Toggle Key.

LCD DISPLAY

WARNING:

DO NOT calibrate operator or operate door unless

doorway is in sight and free of obstructions. Keep people clear of

opening while door is moving.

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

Summary of Contents for GCL-J&H

























































Search results

Summary of Contents for GCL-J&H

Reviews:

Brands by name

Popular brands

Genie GCL-J&H, Installation Manual

Search results

Summary of Contents for GCL-J&H

Reviews:

Brands by name

Popular brands