Genie GCL-J&H Installation Manual Download Page 20

Page: 20 / 56

5.7

Photocell Wiring

NOTE

: Installer must enable PHOTOCELL in calibration mode. See page 6.9.

To Mount Photocells

: (Kit includes detailed Instructions).

Determine location for mounting. They do not need to be directly adjacent to

the door but must be somewhere along the wall where there will be an

unobstructed line between them.

Fig 9

They must extend out away from the wall sufficiently that no door hardware

breaks the plane of the photo-beam.

1) Nominal 24 Volt DC Commercial photocells with normally open contacts can be

connected as shown in

Fig. 8

NOTE

: Blue wire supplies 20 – 40VDC. Photocells used must be compatible with this

voltage range.

NOTE

: If no voltage is present at Blue wire, check fuse F-1 on Control board.

Monitored Photocells

Commercial Non-Monitored Photocells

WARNING:

Photocell systems provide entrapment protection when

mounted near the doorway in such a way that the lower portion of an individual’s

leg will break the photocell beam during normal walking conditions.

WARNING:

Actuating operator using constant contact on the CLOSE button will

override external reversing devices, including photocells.

RESIDENTIAL PHOTOCELLS

CONTROL SIGNAL

TERMINAL STRIP

Figure 7

CONNECT WIRES TO EITHER TERMINAL
(NOT POLARITY SENSITIVE)

Figure 9

N-O

REVERSE

N-O

REVERSE

THRU-BEAM

PHOTOCELLS

CONTROL SIGNAL

TERMINAL STRIP

RECEIVER

TRANSMITTER

EXT RADIO CONNECTOR

PWR

20 40 VDC @ 250mA

MAX CURRENT

RELAY

GND

NOM

+24VDC

RADIO

Blue

Orange

Yello

Figure 8

1) Series II Commercial Monitored photocells and Residential

photocells can be connected to either terminal (they are not polarity sensitive.

( Troubleshooting on page 8.5)

Safe-T-Beam® Monitored Photocells.

Fig. 7 & 8

. Wiring to these

ODC

STB

ODC

STB

www.geniecompany.com

-12

Standard Duty Operator

GCL-J&H

Summary of Contents for GCL-J&H

























































Search results

Summary of Contents for GCL-J&H

Reviews:

Brands by name

Popular brands

Genie GCL-J&H, Installation Manual

Search results

Summary of Contents for GCL-J&H

Reviews:

Brands by name

Popular brands