Genie Chainlift 2020 Operation And Maintenance Manual Download Page 13

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

13

A

Monthly:

Door springs and door hardware:
– Oil door roller, bearings, and hinges using silicone 

lubricant or light oil.

Balance Door.
– Close door.
– Release Carriage Assembly from Rail Assembly by pulling 

down on Emergency Release Knob.

– Raise door manually 3'- 4' and verify that door stays at

that position. See Check Step 2 on page 5.

– Reattach Carriage Assembly to Rail Assembly:

a. Pull the Emergency Release Knob toward Power Head.
b. Close door.

Contact Reverse Test.
– Perform Adjustment Step 2 on page 10.

NOTE

When the door is 3' - 4'  above the ground, the door
should stay open. Slight movement is acceptable. If
the door moves too much, contact a Genie Factory
Authorized Dealer for service or call Customer Service at

1-800-35-GENIE.

WARNING

Do not

operate door automatically or manually if springs

are broken. Contact a Genie Factory Authorized Dealer for
service or call Customer Service at 

1-800-35-GENIE

.

WARNING

If the door fails to reverse on contact with the board,
adjust the Close Force Control as specified in Set Limit
Switches and Force Controls on page 9. If the Opener still
fails, contact a Genie Factory Authorized Dealer for service
or call Customer Service at

1-800-35-GENIE

.

FCC AND IC CERTIFIED

All devices comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received, includ-
ing interference that may cause undesired operation.

WARNING

TO REDUCE THE RISK OF

SEVERE INJURY OR DEATH

1

READ AND FOLLOW ALL INSTRUCTIONS.

2

Never let children operate or play with the Door 
Controls. Keep the Remote Control away from 
children.

3

Always keep the moving door in sight and away 
from people and objects until the door is 
completely closed.

NO ONE SHOULD CROSS THE 

PATH OF THE MOVING DOOR

.

4

NEVER GO UNDER A STOPPED, PARTIALLY 
OPEN DOOR

.

5

Test Opener monthly. The door 

MUST

reverse on 

contact with a 1-1/2" high object (or a 2" x 4" 
board laid flat) at the center of the doorway on the
floor. After adjusting either the Force or the Limit 
of travel, retest the Door Opener. Failure to adjust 
the Opener properly may cause severe injury
or death.

6

When possible use the Emergency Release only 
when the door is closed. Use caution when using 
this Release with the door open. Weak or broken 
springs are capable of increasing the rate of door 
closure and increasing the risk of severe injury 
or death.

7

KEEP GARAGE DOORS PROPERLY BALANCED

.

See Owner's Manual. An improperly balanced 
door increases the risk of  severe injury or death.
Have a  Genie Factory Authorized Dealer make 
repairs to cables, spring assemblies, and other 
hardware.

8

SAVE THESE INSTRUCTIONS.

S

CHEDULED

M

AINTENANCE

WARNING

Use the Wall Console included with Opener. Any other
wall console can cause the Opener to operate 
unexpectedly and the light to stop working.

I

MPORTANT

S

AFETY

I

NSTRUCTIONS

B

As Needed:

Replace Light Bulb

Summary of Contents for Chainlift 2020





















Reviews: