background image

Page 20

11. PREVENTIVE MAINTENANCE

PREVENTIVE MAINTENANCE

EVERY 500 HOURS

EVERY 1500 HOURS

Check oil level

Change oil

  Check / Replace:

 

•  Valves

 

•  Valve seats

 

•  Valve springs

 

•  Valve guides

 Check / Replace:

 

•  H.P packings

 

•  L.P. packings

To guarantee pump reliability and efficiency, respect the maintenance intervals as indicated in the table below.

12. STOPPING THE PUMP FOR LONG PERIODS

12.1 Inactivity For Long Periods

If the pump is started up for the first time after a long period from the shipment date, before starting operation

check the oil level, check the valves as indicated in Chapter 11, and follow the start-up procedures described.

12.2 Filling the Pump With An Anti-Corrosion Emulsion or Anit-freeze By Using An External 

Diaphragm Pump As In The Layout Shown in Paragraph 9.7, between pos. 1 and pos. 2 of fig. 6 and 

fig. 6/a.

a)   In place of a service tank, use a suitable container containing the solution to be pumped.

b)  Close the filter draining, if open.

c)  Be sure that the connecting hose is clean, spread with grease and connect it to the high pressure outlet  

 port.

d)  Fit a suction hose to the membrane pump. Open the pump suction connection and fit hose between it and  

 

the  membrane pump.

e)  Fill the container with the solution/emulsion.

f)  Put the free extremities of the suction line and the high pressure outlet hose inside the container.

g)  Start up the diaphragm pump.

h)  Pump the emulsion until it comes out of the high pressure hose.

i)  Continue pumping for at least another minute; if needed, the emulsion can be reinforced by adding, for  

 

example, Shell Donax

j)  Stop the pump, remove the hose from the suction connection and close it with a plug. 

k)  Remove the hose from the high pressure outlet port. Clean, grease and plug both connections and the  

 hoses.

GENERAL PUMP

A member of the Interpump Group

KF SERIES

ATTENTION: Replace the bearings and the related seal 

rings every 8000 hours of operation. 

Preform periodical checks on cleaning and maintenance 

on the pump. See “ATEX EXPLOSION PROTECTION” 

manual.

Serial #10127003 and later

Ref 300763 Rev. F 

08-21

Summary of Contents for KF Series
































Reviews: