background image

Safety Rules & General Information

2

Installation Guidelines for 60 Hz EcoGen™ Generator

Safety Rules

Study these SAFETY RULES carefully before installing,
operating or servicing this equipment. Become familiar
with this Installation Manual, the Owner’s Manual, and
with the unit. The generator can operate safely, efficiently
and reliably only if it is properly installed, operated and
maintained. Many accidents are caused by failing to
follow simple and fundamental rules or precautions.
The manufacturer cannot anticipate every possible
circumstance that might involve a hazard. The warnings
in this manual and on tags and decals affixed to the unit
are, therefore, not all–inclusive. If using a procedure,
work method, or operating technique the manufacturer
does not specifically recommend, verify that it is safe for
others. Also, make sure the procedure, work method or
operating technique utilized does not render the
generator unsafe.

General Hazards

(000190)

DANGER

Loss of life. Property damage. Installation must always
comply with applicable codes, standards, laws and  
regulations. Failure to do so will result in death  
or serious injury.  

Automatic start-up. Disconnect normal power source 
and render unit inoperable before working on unit. 
Failure to do so will result in death or serious injury.

(000236)

DANGER

(000209a)

WARNING

This product is not intended to be used in  
a critical life support application. Failure to  
adhere to this warning could result in  
death or serious injury.

WARNING

This unit is not intended for use as a prime power 
source. It is intended for use as an intermediate power 
supply in the event of temporary power outage only. 
See individual unit specifications for required 
maintenance and run times pertaining to use.

(000247)

(000187)

WARNING

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery 
cable, then the positive battery cable when working 
on unit. Failure to do so could result in death 
or serious injury.

(000182)

WARNING

(000155)

WARNING

Only a trained and licensed electrician should perform
wiring and connections to unit. Failure to follow proper
installation requirements could result in death, serious
injury, and damage to equipment or property.

(000115)

WARNING

Moving Parts. Do not wear jewelry when 
starting or operating this product. Wearing 
jewelry while starting or operating this product 
could result in death or serious injury.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and 
appendages away from moving parts. Failure 
to do so could result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not 
touch hot surfaces. Keep machine away from 
combustibles during use. Hot surfaces 
could result in severe burns or fire.

WARNING

Risk of injury. Do not operate or service this 
machine if not fully alert. Fatigue can impair the 
ability to service this equipment and could result 
in death or serious injury.

(000215)

(000146)

WARNING

Equipment and property damage. Do not alter  
construction of, installation, or block ventilation for  
generator. Failure to do so could result in unsafe  
operation or damage to the generator.

Summary of Contents for ecoGen G0061030

























































Reviews: