background image

Safety Rules & General Information

4

Owner’s Manual for Australian 50 Hz Air-Cooled Generators

Fire Hazards

Comply with regulations the local agency for workplace
health and safety has established. Also, verify that the
generator set is installed in accordance with the manu-
facturer’s instructions and recommendations. Following
correct installation, do nothing that might alter a safe
installation and render the unit in noncompliance with the
aforementioned codes, standards, laws, and regulations.

Explosion Hazards

Battery Hazards

WARNING

(000217)

Fire hazard. Do not obstruct cooling and ventilating 
airflow around the generator. Inadequate ventilation 
could result in fire hazard, possible equipment 
damage, death or serious injury.

WARNING

(000218)

Fire and explosion. Installation must comply with all 
local, state, and national electrical building codes. 
Noncompliance could result in unsafe operation, 
equipment damage, death, or serious injury.

WARNING

Fire hazard. Use only fully-charged fire extinguishers 
rated according to applicable industry standards. 
Improperly rated fire extinguishers will not extinguish 
electrical fires in standby generators. 

(000252)

(000100a)

Consult Manual. Read and understand manual
completely before using product. Failure to 
completely understand manual and product 
could result in death or serious injury.

WARNING

WARNING

Electrocution. Refer to local codes and standards for 
safety equipment required when working with a live 
electrical system. Failure to use required safety 
equipment could result in death or serious injury.

(000257)

(000147)

WARNING

Risk of Fire. Unit must be positioned in a
manner that prevents combustible material
accumulation underneath. Failure to do so
could result in death or serious injury.

(000192)

DANGER

Explosion and fire. Fuel and vapors are extremely
flammable and explosive. No leakage of fuel is
permitted. Keep fire and spark away. Failure to do
so will result in death or serious injury.

(000151a)

DANGER

Explosion and fire. Connection of fuel source must be 
completed by a qualified professional technician or contractor. 
Incorrect installation of this unit will result in death, serious 
injury, and property and equipment damage.

(000174)

DANGER

Risk of fire. Allow fuel spills to completely dry 
before starting engine. Failure to do so will 
result in death or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite 
combustibles, resulting in fire. Fire could 
result in death or serious injury.

(000188)

DANGER

Electrocution. Do not wear jewelry while 
working on this equipment. Doing so will 
result in death or serious injury.

(000162)

Explosion. Do not dispose of batteries in a fire. 
Batteries are explosive. Electrolyte solution can cause 
burns and blindness. If electrolyte contacts skin or eyes, 
flush with water and seek immediate medical attention.

WARNING

(000137a)

WARNING

Explosion. Batteries emit explosive gases while 
charging. Keep fire and spark away. Wear protective 
gear when working with batteries. Failure to do so 
could result in death or serious injury.

Summary of Contents for 10 KVA









































Reviews: