background image

16 Generac

®

Power Systems, Inc.

Safety Rules

IMPACT-36 plus II Recreational Vehicle Generator

NOTICE TO INSTALLER

These 

Installation Instructions

have been published

by Generac to aid in the installation of the products
described in this manual. Generac assumes that
installation personnel are familiar with the procedures
for installing such products, or similar products that
Generac manufactures. Generac also assumes that
personnel have been trained in the recommended
installation procedures for these products and that
such training includes (a) use of common hand tools,
(b) use of special Generac tools, and (c) use of any
tools and/or equipment from other suppliers.

Generac cannot possibly know of, nor advise the
recreational vehicle trade of, all conceivable methods,
procedures, or techniques by which to perform an
installation. Nor can Generac anticipate every possi-
ble hazard that might result from each installation
method, procedure, or technique. Generac has not
undertaken any such wide evaluation. Therefore,
people who use a method, procedure, or technique
that Generac does not specifically recommend must
first completely satisfy themselves that their safety,
the safety of the vehicle's occupants, and the prod-
uct's safety are not endangered by the method, pro-
cedure, or technique selected.

Information, illustrations, specifications, etc., con-
tained in these 

Installation Instructions

are based on

the latest information available at the time of publi-
cation. Every effort has been expended to be sure that
such data are both accurate and current. However,
the manufacturer reserves the right to change, alter,
or otherwise improve this product at any time, with-
out prior notice.

Despite the safe design of this generator, 
operating this equipment imprudently, neglecting
its maintenance, or being careless can cause 
possible injury or death. Permit only responsible
and capable persons to operate or maintain this
equipment.

Parts of the generator are rotating and/or hot
during operation. Exercise care near running
generators. 

Potentially lethal voltages are generated by
these machines. Ensure all steps are taken to
render the machine safe before attempting to
work on the generator.

GENERAL HAZARDS

• For safety reasons, Generac recommends that the

installation, initial startup, and maintenance of
this equipment is carried out by a Generac
Authorized Service Dealer.

• The engine exhaust fumes contain carbon monox-

ide, which can be DEADLY. This dangerous gas, if
breathed in sufficient concentrations, can cause
unconsciousness or even death. This exhaust sys-
tem must be installed properly, in strict compli-
ance with applicable codes and standards.
Following installation, do nothing that might ren-
der the system unsafe or in noncompliance with
such codes and standards. The generator com-
partment must be completely vapor-sealed from
the vehicle interior. There must be no possibility of
exhaust fumes entering the vehicle interior. Never
operate this equipment with a leaking or defective
exhaust system.

• Keep hands, feet, clothing, etc., away from drive

belts, fans, and other moving or hot parts.
Never remove any drive belt or fan guard while
the unit is operating.

• Adequate, unobstructed flow of cooling and ven-

tilating air is critical to correct generator oper-
ation and is required to expel toxic fumes and
fuel vapors from the generator compartment.
Without sufficient cooling airflow, the
engine/generator quickly overheats, which caus-
es serious damage to the generator. Do not alter
the installation or permit even partial blockage
of ventilation provisions, as this can seriously
affect safe operation of the generator.

• When working on this equipment, remain alert at

all times. Never work on the equipment when
physically or mentally fatigued.

• Before performing any maintenance on the genera-

tor, disconnect its battery cables to prevent acci-
dental startup. First, disconnect the cable from the
battery post, indicated by a NEGATIVE, NEG, or
(–). Reconnect that cable last.

• Never use the generator or any of its parts as a

step. Stepping on the unit can stress and break
parts, and may result in dangerous operating con-
ditions from leaking exhaust gases, fuel leakage,
oil leakage, etc.

• Never insert any tool or other object through open-

ings in the generator interior, even if the unit is not
running. Seriouse injury or damage to the equip-
ment may occur.

!

!

!

!

DANGER

DANGER: For fire safety, installation of a generator into a recreational vehicle must comply
strictly with NFPA 70 (latest edition), “National Electrical Code”, Article 551, and NFPA 1192
(latest edition), “Standard for Recreational Vehicles”. In addition, installation must comply with
the manufacturer’s instructions and recommendations.

!

!

Summary of Contents for 00941-4





















































Reviews: