background image

2

• Never start or stop the unit with electrical loads connected 

to receptacles AND with connected devices turned ON. Start 

the engine and let it stabilize before connecting electrical 

loads. Disconnect all electrical loads before shutting down the 

generator.

•  Do not insert objects through unit’s cooling slots.
• When working on this equipment, remain alert at all times. 

Never work on the equipment when physically or mentally 

fatigued.

•  Never use the generator or any of its parts as a step. Stepping 

on the unit can stress and break parts, and may result in 

dangerous operating conditions from leaking exhaust gases, 

fuel leakage, oil leakage, etc.

NOTE:

This generator is equipped with a spark arrestor muffler. The 

spark arrestor must be maintained in effective working order 

by the owner/ operator. In the State of California, a spark 

arrestor is required by law (Section 4442 of the California 

Public Resources Code). Other states may have similar laws. 

Federal laws apply on federal lands. 

EXHAUST & LOCATION HAZARDS

•  Never operate in an enclosed area or indoors! NEVER use in 

the home, in a vehicle, or in partly enclosed areas such as 

garages, EVEN IF doors and windows are open! ONLY use 

outdoors and far from open windows, doors, vents, and in an 

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which 

you cannot see or smell. This poisonous gas, if breathed in 
sufficient concentrations, can cause unconsciousness or even 
death.

• Adequate, unobstructed flow of cooling and ventilating air 

is critical to correct generator operation. Do not alter the 
installation or permit even partial blockage of ventilation 
provisions, as this can seriously affect safe operation of the 
generator. The generator MUST be operated outdoors. 

•  This exhaust system must be properly maintained. Do nothing 

that might render the exhaust system unsafe or in noncompliance 

with any local codes and/or standards.

•  Always use a battery operated carbon monoxide alarm indoors, 

installed according to the manufacturer's instructions.

•  If you start to feel sick, dizzy, or weak after the generator has 

been running, move to fresh air IMMEDIATELY. See a doctor, as 
you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in 

operation. Avoid contact with bare wires, terminals, connections, 

etc., while the unit is running, even on equipment connected 

to the generator. Ensure all appropriate covers, guards and 

barriers are in place before operating the generator. 

• Never handle any kind of electrical cord or device while 

standing in water, while barefoot or while hands or feet are wet. 

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

•  The National Electric Code (NEC) requires the frame and external 

electrically conductive parts of the generator be properly 

connected to an approved earth ground. Local electrical codes 

may also require proper grounding of the generator. Consult 

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly 

conductive area (such as metal decking or steel work).

•  Do not use worn, bare, frayed or otherwise damaged electrical 

cord sets with the generator.

•  Before performing any maintenance on the generator, disconnect  

the engine starting battery (if equipped) to prevent accidental 

start up. Disconnect the cable from the battery post indicated 

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

•  In case of accident caused by electric shock, immediately shut 

down the source of electrical power. If  this is not possible, 
attempt to free the victim from the live conductor. 

AVOID 

DIRECT CONTACT WITH THE VICTIM. 

Use a non-conducting 

implement, such as a rope or board, to free the victim from the 
live conductor. If the victim is unconscious, apply first aid and 
get immediate medical help.

FIRE HAZARDS

•  Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE. 

Do not permit smoking, open flames, sparks or heat in the 
vicinity while handling gasoline. 

•  Never add fuel while unit is running or hot. Allow engine to cool 

completely before adding fuel.

• Never fill fuel tank indoors. 

Comply with all laws regulating 

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel 

expansion. 

If tank is over-filled, fuel can overflow onto a hot 

engine and cause FIRE or an EXPLOSION. Never store generator 

with fuel in tank where gasoline vapors might reach an open 

flame, spark or pilot light (as on a furnace, water heater or 

clothes dryer). FIRE or EXPLOSION may result. Allow unit to 

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no 

combustible materials are left on or near the generator. Keep the 
area surrounding the generator clean and free from debris and 
keep a clearance of five (5) feet on all side to allow for proper 

Safety Rules

Summary of Contents for 005622-0





































Reviews: