Generac Power Systems 004709-0 Owner'S Manual Download Page 8

 6 

n

 

 The manufacturer does not recommend 

using any gasoline containing alcohol (such 

as “gasohol”). If using any gasoline contain-

ing alcohol, it must not contain more than 

10 percent ethanol, and it must be removed 

from the generator during storage. Do NOT 

use any gasoline containing methanol. If 

using gasoline with alcohol, inspect more 

frequently for fuel leaks and other abnor-

malities.

1.5.2 FUEL 

CONSUMPTION

Model

No Load

1/2 Load

Full Load

004709-0

0.24

0.35

0.55

Fuel consumption is in gal/hr.

1.5.3  ENGINE OIL REQUIREMENTS

Use only high quality detergent oil rated with American Petroleum 

Institute (API) Service Classification SF, SG or SH. The recom-

mended oil weights include the following:

During summer months: SAE 30. An acceptable substitute is 

• 

SAE 10W-30.

During winter months: SAE 5W-30. DO NOT USE SAE 

• 

10-W40.

Crankcase and oil filter capacity is approximately 800 mL or .84 

U.S. quarts. Do NOT use special additives. See sections "Checking 

the Engine Oil Level" and "Changing the Engine Oil and/or Oil Filter" 

for oil level check and fill procedures.

1.5.4 ENGINE

Type of Engine ............................................................GN-220, Single-cylinder
Cooling Method ................................................................................Air-cooled
Rated Horsepower ...............................................................7.8 @ 4,200 rpm
Displacement ......................................................................................... 220cc
Cylinder Block ....................................................Aluminum w/Cast Iron Sleeve
Type of Governor ...................................................... Mechanical, Fixed Speed
Air Cleaner ................................................. Paper Element w/Foam Precleaner
Starter .................................................................................12-volt DC Electric
Ignition System ..............................................Solid-state w/Flywheel Magneto
Recommended Spark Plug
  Champion ......................................................................................... RC14YC
  AC ..........................................................................................................R45S
  Fram Autolite .............................................................................................. 65
Spark Plug Gap ................................................................0.030 inch (76 mm)
Recommended Minimum Battery .......................................  400 Cold-cranking

Amperes

1.5.5 GENERATOR

Rated Maximum Continuous 

  AC Output (Gasoline) ...................................................3,600 Watts (3.6 kW)
Rated Voltage ...............................................................................120 Volts AC
Rated Maximum Continuous 

  AC Current (Gasoline).................................................................30 Amperes
Phase ......................................................................................................Single
Rotor RPM .............................................................................................. 3,600
Number of Rotor Poles ...................................................................................2
Engine RPM ............................................................................................ 3,600
Rated AC Frequency ............................................................................... 60 Hz
Battery Charge Voltage ..................................................................14 Volts DC
Battery Charge Current .........................................................2 Amperes (max)
Gasoline weight ............................................................................ 170 Pounds
Length ............................................................................749.8 mm (29.52 in.)
Width .............................................................................483.1 mm (19.02 in.)
Height ............................................................................342.2 mm (13.47 in.)

*  Maximum wattage and current are subject to, and limited by, such factors as 

fuel Btu content, ambient temperature, altitude, engine condition, etc.. Maximum 
power decreases about 3.5% for each 1,000 feet above sea level; and will 
also decrease about 1% for each 6° C (10° F) above 16° C (60° F) ambient 
temperature.

1.5.6  EMISSIONS COMPLIANCE PERIOD

For non-handheld engines the Emissions Compliance Period 

referred to on the Emissions Compliance Label indicates the num-

ber of operating hours for which the engine has been shown to 

meet Federal emission requirements.

For engines less than 225 cc displacement, Category C=125 

• 

hours, B=250 hours, and A=500 hours.

For engines of 225 cc or more, Category C=250 hours, B=500 

• 

hours, and A=1000 hours.

1.5.7  EVAPORATIVE EMISSIONS INFORMATION

This generator is subject to evaporative emission standards which 

have been implemented by the California Air Resource Board 

(CARB) and the Environmental Protection Agency (EPA). If this 

generator is offered for sale in the state of California, it must be 

covered by a CARB evaporative Executive Order. If this generator 

is offered for sale to the final consumer in any other state, certified 

low-permeation fuel line must be used to supply fuel to the genera-

tor as required by EPA.
Anyone who installs or configures a fuel system to supply this 

generator with gasoline is required to comply with all applicable 

evaporative emission regulations. If this generator is configured 

such that it shares the primary fuel system of a vehicle in which it 

is installed, reduced certification requirements may apply. See the 

CARB guidance document MAC 05-05, located at http://www.arb.

ca.gov/msprog/macs/mac0505/mac0505.pdf for further details. If 

this generator is installed such that it uses a dedicated fuel system, 

detailed evaporative emission requirements apply; contact a repu-

table fuel system manufacturer to purchase a complete fuel sys-

tem certified for use with this generator, or consult the California 

Code of Regulations if you wish to obtain certification on your 

own. See the installation instructions in this manual for connecting 

fuel system vapor lines to the engine.

General Information

Summary of Contents for 004709-0





















































Reviews: