background image

2

Generac

®

Power Systems, Inc.

Study these SAFETY RULES carefully before installing,
operating or servicing this equipment. Become familiar
with this 

Owner’s Manual

and with the unit. The gen-

erator can operate safely, efficiently and reliably only if
it is properly installed, operated and maintained. Many
accidents are caused by failing to follow simple and fun-
damental rules or precautions.

Generac cannot possibly anticipate every possible 
circumstance that might involve a hazard. The warn-
ings in this manual, and on tags and decals 
affixed to the unit are, therefore, not all-inclusive. If you
use a procedure, work method or operating technique
Generac does not specifically recommend, you must
satisfy yourself that it is safe for you and others. You
also must make sure the procedure, work method or
operating technique that is chosen does not render the
generator unsafe.

Despite the safe design of this generator, 
operating this equipment imprudently, neglecting its
maintenance or being careless can cause 
possible injury or death. Permit only responsible and
capable persons to operate or maintain this equip-
ment.

Potentially lethal voltages are generated by these
machines. Ensure all steps are taken to render the
machine safe before attempting to work on the
generator.

Parts of the generator are rotating and/or hot
during operation. Exercise care near running gen-
erators. 

GENERAL HAZARDS

• For safety reasons, Generac recommends 

that the installation, initial start-up and maintenance
of this equipment is carried out by a
Generac/Guardian Authorized Dealer.

• Installation, operation, servicing and repair of this

(and related) equipment must always comply with
applicable codes, standards, laws and regulations.
Adhere strictly to local, state and national electrical
and building codes.  Comply with regulations the
Occupational Safety and Health Administration
(OSHA) has established.  Also, ensure that the gener-
ator is installed, operated and serviced in accordance
with the manufacturer’s instructions and recommen-
dations.  Following installation, do not do anything
that might render the unit unsafe or in noncompli-
ance with the aforementioned codes, standards, laws
and regulations.

• The engine exhaust fumes contain carbon monoxide,

which can be DEADLY. This dangerous gas, if
breathed in sufficient concentrations, can cause
unconsciousness or even death. For that reason, ade-
quate ventilation must be provided.  Exhaust gases
must be piped safely away from any building or
enclosure that houses the generator to an area where
people, animals, etc., will not be harmed.  This
exhaust system must be installed properly, in strict
compliance with applicable codes and standards.

• Keep hands, feet, clothing, etc., away from drive belts,

fans, and other moving or hot parts. Never remove
any drive belt or fan guard while the unit is operating.

• Adequate, unobstructed flow of cooling and ventilating

air is critical in any room or building housing the gen-
erator to prevent buildup of explosive gases and to
ensure correct generator operation. Do not alter the
installation or permit even partial blockage of ventila-
tion provisions, as this can seriously affect safe oper-
ation of the generator.

• Keep the area around the generator clean and unclut-

tered.  Remove any materials that could become haz-
ardous.

• When working on this equipment, remain alert at all

times. Never work on the equipment when you are
physically or mentally fatigued.

!

!

!

!

DANGER

Important Safety Instructions

Guardian Liquid-cooled 40 kW Generator

SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe 
operation be copied and posted in potential hazard areas. Safety should be stressed to all
operators and potential operators of this equipment.

!

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

!

!

!

SAVE THESE INSTRUCTIONS – This manual contains important instructions that should be
followed during installation and maintenance of the generator and batteries.

!

!

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

!

!

Summary of Contents for 004626-1





























































Reviews: