Figure 6: The curve above shows the effect of the ‘treble tilt’, ‘bass tilt’
and ‘bass roll-off’ controls on the free field response.
Figure 7: The curve group shows the horizontal directivity characteristics
of the 1029A in its vertical configuration measured at 1m. The lower
curve shows the systems power response.
Bass amplifier output power with an 8 Ohm load: 40 W
Treble amplifier output power with an 8 Ohm load: 40 W
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at nominal output:
THD < 0.08%
SMPTE-IM < 0.08%
CCIF-IM < 0.08%
DIM 100 < 0.08%
Signal to Noise ratio, referred to full output:
Bass > 90 dB
Treble > 90 dB
Mains voltage:
100/200, 115/230 or 230 V
according to region
Voltage operating range: ±10%
Power consumption: Idle 9 VA
Full output 80 VA
Lower cut-off frequency, –3 dB: < 68 Hz
Upper cut-off frequency, –3 dB: > 20 kHz
Free field frequency response of system:
70 Hz –18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on axis
in half space, averaged from 100 Hz to 3 kHz:
@ 1m > 100 dB SPL
@ 0.5m > 106 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver unit
protection circuit): @ 1m > 98 dB SPL
@ 0.5m > 104 dB SPL
Maximum peak acoustic output per pair on top of
console, @ 1 m from the engineer with music material:
> 110 dB
Self generated noise level in free field @ 1m on axis:
< 10 dB (A-weighted)
Harmonic distortion at 85 dB SPL @ 1m on axis:
Freq: 75…150 Hz < 3%
> 150 Hz < 1%
Drivers: Bass 130 mm (5") cone
Treble 19 mm (
3
/
4
") metal dome
Both drivers are
magnetically shielded
Weight: 5.7 kg (12.5 lb)
Dimensions: Height 247 mm (9
3
/
4
")
Width 151 mm (5
15
/
16
")
Depth 191 mm (7
1
/
2
")
Inputs: Input 1: XLR female, balanced 10 kOhm
Input 2:
1
/
4
" Jack socket, balanced 10 kOhm
Input level for 100 dB SPL output at 1 m:
-6 dBu at volume control max
Volume control range:
>70 dB relative to max output
Subsonic filter below 68 Hz : 18 dB/octave
7050A/1091A Subwoofer output (input 2) at 100db SPL:
–23 dBu into 33kOhm load
Ultrasonic filter above 25 kHz: 12 dB/octave
Crossover frequency, Bass/Treble: 3.3 kHz
Crossover acoustical slopes:
24–32 dB/octave
Treble tilt control operating range:
0 to –2 dB @ 15 kHz
Bass roll-off control operating in a –6 dB step @ 85 Hz
(to be used in conjunction with 7050A or 1091A
subwoofer)
Bass tilt control operating range in –2 dB steps:
0 to –6 dB @ 150 Hz
The ‘CAL’ position is with all tone controls set to ‘off’ and
the input sensitivity control to maximum (fully
clockwise).
AMPLIFIER SECTION
CROSSOVER SECTION
SYSTEM SPECIFICATIONS
International enquiries:
Genelec Oy, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83 881
Fax +358 17 812 267
Email [email protected]
In the U.S. please contact
Genelec Inc., 7 Tech Circle
Natick, MA 01760
Phone +1 508 652 0900
Fax +1 508 652 0909
Email [email protected]
www.genelec.com
Genelec Document BBA29001a. Copyright Genelec Oy 1.2003. All data subject to change without prior notice
1029A Data Sheet
1029A_DA.IND 4
27.1.2003, 12:57:16
