background image

FAQ

17

 

1. How do I change the Handset IDs?

To change the handset id, use the following steps in sequence:

Keep the ‘/’ key pressed for a few seconds until a ‘?’ appears on the display screen.

If the ‘/’ also appears on the display screen, then erase it using the ‘del’ key.

Type 1234 on the keypad and press the “Delta” or “Chart” key if using the Teacher 

handset.

‘ID=’ will be displayed on the screen.

Enter the handset id you want to be allocated to the handset in three digit format. For 

example, to set the handset id to 1, enter 001 on the keypad.

Note: 

Handset id must be between “000” and “255” excluding “126” and “206”.

Press the “Delta” key again. Handset id will be set to the number entered. This can be 

confirmed by checking the number being displayed in the upper-right corner of the 

handset screen.

2. How do I reset the handsets?

Use a sharp, pointed object to press the small button located on the back of the hand-

set. Use this when handset will not map correctly, freezes or with charging problems.

3. What is “Mapping” handsets? When do I need to do this?

Each receiver has a unique ID as shown on the receiver ID label. All handsets are 

locked into communicating with a receiver. If you want to lock a handset to work with a 

different/new receiver you must press and hold down the “?” key until the handset has 

mapped. This can take several seconds. When you see the up/down arrows flashing on 

the handset LCD, the handset is locked to the new receiver. Please note that when 

locking handsets the distance between handset and receiver should be a approx 50-

75mm.

4. How long do I have to re-charge the Genee Pad handsets for?

7 to 10 hours charge is normally needed to fully charge a totally flat handset. If a hand-

set has a small amount charge a 2 hour booster charge is needed. The length of time 

between charging will depend upon the usage.

5. What technology does the response system use and what is the 

range?

The system uses RF with operating frequency bands 2405 MHz to 2485 MHz (2.4 

GHz). The maximum transmission range is 50m.

Conference settings

Response system set-up example 2:

‘We are carrying out Health & Safety training with groups of our employees. It is impor-

tant that we have records of individual attainment so that we know who will be compe-

tent in particular work situations. What is the best way to set up?’

1. Check that ClassComm is in the correct 

mode for you (education or corporate) by 

going to 

Settings > Application mode

 

(you will have to restart ClassComm to 

activate this setting).

2. After you have chosen your resource 

slides, go to the 

Presentation

 window.

3. Select 

Record Assessment 

to keep 

results and publish data.

4. Select 

Ad Hoc Presentation

 and 

New 

Group

 to build the group participant list.

5. Click on 

Capture Names 

and ask par-

ticipants to text in their names using the 

hand-sets. When all have done so, click on 

Stop Capture

 and 

Done

.

16

 

1

2

3

4

5

6

7

9

6. Enter a 

Group Name

 and click on 

Save

. (if this group stays the same, you 

can recall it for further assessments to be 

added to the participants’ data).

7. Select any other options of your choos-

ing from the 

Test Settings

 window such 

as 

Participant Feedback

 or 

Single Re-

sponse.

8. Save these as your 

Default Setting

 

ready for repeat sessions.

9. Click on 

Present Activity

 to start the 

presentation.

Summary of Contents for iQ-Pad











Reviews: