background image

P.04

6. Close the amber lid above the gel.

7. Now the fluorescent samples can be viewed or cut.

8. When finishing, turning the transilluminator off.

9. Clean the transilluminator filter and surface by wiping with a wet, not scratching cloth.

Troubleshooting

This table below lists the most common problems which you may encounter during using 

the 

μ

BLooK

TM

 LED transilluminator

Related Ordering Information

Note: Please, read the installation instruction carefully before installing the 

μ

BLooK

TM

 LED transilluminator.

This instrument is intended for clinical and research laboratory use and it must be operated 

only by specialized personnel aware of the potential risks associated with the chemical and 

biological agents normally used with this unit. This instrument is meant for use only by 

specialized personnel that know the health risks associated with blue light radiation and with 

reagents that are normally used with this instrument. It is designed to shield only the person 

working in front of the system and to observe the gel fluorescence emission clearly.

       

Maintenance and Repair

Cleaning and Maintenance

The transilluminator should be damply wiped off with a soft cotton cloth. The cloth should not 

be too wet. Do not use aggressive cleaning detergents or solvents.

After use of the transilluminator, we recommend to wipe off the frame and the filter glass with 

a damp cloth. Take care that the cloth is not soaked with scrubbing or corrosive detergents 

as this could damage the filter glass. We suggest using alcohol, glass cleaners or similar 

mild detergents.

Pay attention to wearing appropriate gloves when cleaning areas (as the filter plate of the 

transilluminator, switches, protection shield) which may have been in contact with carcino-

genic or toxic reagents. The protection shield is made of tempered glass and must only be 

cleaned with a damp cloth.

Problem

Low sensitivity

          

High background, 

suboptimal, or no image

Cause

Wavelength may not 

be right

          
Low sample 

concentration

Solution

Check the excitation and 

emission wavelengths of 

the fluorescence dye
Check the concentration 

of sample

Cat. No.

SL001-1000
SL002-0500
SM203-0100
SM205-0100
SM206-0100
SM207-0100

Description

Novel Juice
Novel Green
OnePCR

TM

OnePCR

TM

 HiFi

OnePCR

TM

 HotStar

OnePCR

TM

 

Plus

Size

1 ml

500 μl

100 Reactions
100 Reactions
100 Reactions
100 Reactions

Summary of Contents for uBLOOK BK003-000W








Reviews: