GenBody Confiscope g20 User Manual Download Page 7

1.

 

Warnings and Precaution for Safety 
1.1

 

Warnings and Precaution for Safety   
1.1.1  For  safety  purposes,  please  ensure  to  read  user manual  thoroughly 
before using this device. 
 
1.1.2  In  this  user  manual,  no  calibration  of  the  product,  repair  or 
maintenance  stated.  In  the  event  of  technical  issues,  please  contact  the 
authorized dealer or GenBody Inc. for service. 
 
1.1.3  Do  not  disassemble,  repair  or  modify  the  machine  without  any 
permission. 
 
1.1.4  GenBody  is  not  responsible  for  malfunctions  and  damage  to  the 
product caused by irregular operation that is not mentioned in this manual. 
 

1.2

 

Precautions for Installation the Product 
1.2.1 Do not install in an unsafe place. 
 
1.2.2 Do not install near inflammable objects or contaminated places.   
 
1.2.3 Do not install  in areas where moisture is high or exposed to direct 
sunlight, near heaters or near magnetic objects. 
 
1.2.3 Make sure to use provided AC-DC adapter. 
 
1.2.4 Plug the power cable to the grounded power outlet. Plugging to the 
ungrounded power outlet may cause device failure as well as electric shock. 
 
1.2.5 Install the outlet in an easily accessible location. In event of technical 
issues, please disconnect the plug completely to turn off the power. 
 
1.2.6 Do not drop or shock the product when moving. 
 
1.2.7 Be careful as there is a biological risk of cross-infection. 
 

1.3

 

Precautions before Use 

Summary of Contents for Confiscope g20





























Reviews: