manualshive.com logo in svg

Gemu ACTRONIC Profibus DP, Operating Instructions Manual

Share
Download
Gemu ACTRONIC Profibus DP Operating Instructions Manual Download Page 6

 

ACTRONIC

® 

Profibus DP

 

Operating instructions

 

SideStep

® 

Industrial 

OPEN/CLOSE

 

 

 

 

 

 

 

 

 

 

6/42

 

5.  Bus wiring via drop cable 

 
 

With a transmission rate 

≤

 1.5Mbaud.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

6.  Different configuration menu 

 
The GEMÜ SideStep with Profibus DP has the following expanded configuration menu 
compared to the standard SideStep: 
 
 
 
 
 
 
 
 
 
 
 
 

DP Adr 

Determines the Profibus address of the actuator. 
 

PwrOnT.Out 

Defines the time between error recognition and message when the actuator is switched 
on. 

Profibus
terminating 
resistor

Service

1

SetBasics

2

 

 

 

SetFunction    

   

3

SetCalibration

   

4

     Return

6       

SETUP

Communication    

5

Fieldbus

5.2

IR-Port

5.1

DP adrr   

 26

     Return

       

PwrOnT.Out

Summary of Contents for ACTRONIC Profibus DP











































Reviews:

No comments

Brands by name

Popular brands

Load more brands