manualshive.com logo in svg

Gemu ACTRONIC Profibus DP, Operating Instructions Manual

Share
Download
Gemu ACTRONIC Profibus DP Operating Instructions Manual Download Page 18

 

ACTRONIC

® 

Profibus DP

 

Operating instructions

 

SideStep

® 

Industrial 

OPEN/CLOSE

 

 

 

 

 

     18/42

 

8.  External diagnostic errors 

 

Defined error messages: 

Error ID 

Error 

0x01  

Data length service data from master to slave incorrect 

0x02  

Data length service data from slave to master incorrect 

0x20 

Specified parameter value too low 

0x21 

Specified parameter value too high 

0x22 

Parameter does not exist 

0x30  

Error in SideStep  

0x31  

Error in SideStep acknowledged 

0x32 

Warning in SideStep  

0x33 

Warning in SideStep acknowledged 

0x34 

No error list entry on the requested number available  

0x40 

Event active in SideStep, therefore no new event possible. 

0x41 

Active action cannot be affected by Profibus 

0x42 

NoInit not available 

0x43 

Event doesn´t exist 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for ACTRONIC Profibus DP











































Reviews:

No comments

Brands by name

Popular brands

Load more brands