6.
保养
Cleaning
6-1.
旋梭的清扫
Cleaning the rotary hook
6-2.
控制箱进气口的清扫
Cleaning the control box air inlet ports
6-3.
更换润滑油
Draining the oil
6-4.
护眼板的清洁
Cleaning the eye guard
6-5.
机针的检查
Checking the needle
6-6.
加油
Lubrication
7.
标准调整
Standard adjustments
7-1.
头部开关的确认
Checking the machine head switch
7-2.
挑线弹簧的调整
Adjusting the thread take-up spring
7-3.
机壳线导向
R
的调整
Adjusting arm thread guide R
7-4.
针杆高度的调整
Adjusting the needle bar height
7-5.
针杆上升量的调整
Adjusting the needle bar lift amount
7-6.
梭托导针部的调整
Adjusting the drive needle guard
7-7.
针隙的调整
Adjusting the needle clearance
7-8.
旋梭导线器的调整
Adjusting the shuttle race thread guide
7-9.
旋梭供油量的调整
Adjusting the rotary hook lubrication amount
7-10.
动刀的位置调整
Adjusting the position of the movable knife
7-11.
动刀和定刀的更换方法
Replacing the movable and fixed knives
7-12.
扫线器的调整
Adjusting the thread wiper
7-13.
间歇压脚的安装位置
Presser foot installation position
7-14.
间歇压脚行程的变换
Changing the intermittent storke
7-15.
压脚上升量的调整
Adjusting the work clamp lift amount
7-16.
空气压力的调整
(
空压规格
) Adjusting the air pressure (pneumatic specifications)
8.
故障检修
Troubleshooting
...................................................................................17
................................................................17
............................................18
........................................................................18
...............................................................18
....................................................................19
..................................................................................19
................................................................19
..................................................20
..................................................20
....................................................21
......................................................21
................................................21
...................................................22
..........................................................22
.............................................23
........................................23
..........................................24
.......................................25
...........................................................26
................................................27
................................................27
.............................................29
........................29
......................................................................29
Ⅷ
Summary of Contents for GEM2210/1310
