Gemini 810 User Manual Download Page 43 | Manualshive

Page: 43 / 56

background image

REGULATORY COMPLIANCE

FCC/INDUSTRY CANADA TWO PART STATEMENT

PER INDUSTRY CANADA RSS RULES:

This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of

the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil

ne doit pas produire de brouillage, et (2) I’utilisateur de I’appareil doit accepter tout brouillage

radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.

This device complies with Health Canada’s Safety Code. The installer of this device should ensure

that RF radiation is not emitted in excess of Health Canada’s requirement.

Information can be obtained at

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-

lignes_direct/index-eng.php

Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de

cet appareil doit s’assurer que les rayonnements RF n’est pas émis au-delà de l’exigence de Santé

Canada.

Les informations peuvent être obtenues:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_

guide-lignes_direct/index-eng.php

43

«
...
41
42
43
44
45
...
»

Summary of Contents for 810

























































Reviews:

No comments

Related manuals for 810

Brand: Campbell Pages: 25

Brand: Larson Davis Pages: 2

Brand: G-Tek Pages: 27

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Olympus Pages: 12

Brand: janitza Pages: 48

Brand: Teledyne Analytical Instruments Pages: 107

Brand: Kirby Morgan Pages: 101

Brand: BASI Pages: 69

Brand: Leutert Pages: 8

Brand: Hanna Instruments Pages: 52

Brand: LI-COR Pages: 92

Brand: Teletek electronics Pages: 2

Brand: Oakton Pages: 80

Brand: i-SENS Pages: 133

Brand: E Instruments Pages: 2

Brand: Lapp Automaatio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands