Gemini 810 User Manual Download Page 12 | Manualshive

Page: 12 / 56

background image

OVERVIEW - FIBER DELIVERY SYSTEM

The fiber delivery system is a unique and ergonomic optical cable that is non-detachable from

the laser unit. The handpiece will require cleaning and sterilization after each patient treatment.

Disposable tips are intended for single-use only and must be disposed of after each patient use.

Refer to page 30 for cleaning and sterilization procedures.

Anodized Aluminum Handpiece

Optical Ferrule

Bendable Stainless Steel Tube

Optical Fiber

Fiber Strain Relief

Illumination Tip

12

Turn counter-clockwise
(Remove to Sterilize)

«
...
10
11
12
13
14
...
»

Summary of Contents for 810

























































Reviews:

No comments

Related manuals for 810

Brand: Daewoo Pages: 2

Brand: Hameg Pages: 44

Brand: Hameg Pages: 60

Brand: Hameg Pages: 28

Brand: HAMAR LASER Pages: 113

Brand: Larson Davis Pages: 536

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brand: Dewetron Pages: 24

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: Bontempi Pages: 18

Brand: Sonel Pages: 84

Trimble Ranger 3

Brand: Badger Meter Pages: 20

Brand: A&D Pages: 38

Brand: S&T Pages: 23

Brand: Hanna Instruments Pages: 32

Brand: Fluke Pages: 22

Thruline 4020 Series

Brand: Bird Electronic Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands