background image

 

V 02/22 

 

 

Documentation Enamel Automatic Gun OptiGun GA03-E 

 

© Copyright 2012 Gema Switzerland GmbH 

All rights reserved. 

 

This publication is protected by copyright. Unauthorized copying is prohib-
ited by law. No part of this publication may be reproduced, photocopied, 
translated, stored on a retrieval system or transmitted in any form or by 
any means for any purpose, neither as a whole nor partially, without the 
express written consent of Gema Switzerland GmbH. 

MagicCompact, MagicCylinder, MagicPlus, MagicControl, OptiFlex, Opti-
Control, OptiGun, OptiSelect, OptiStar and SuperCorona are registered 
trademarks of Gema Switzerland GmbH. 

OptiFlow, OptiCenter, OptiMove, OptiSpeeder, OptiFeed, OptiSpray, Op-
tiSieve, OptiAir, OptiPlus, OptiMaster, MultiTronic, EquiFlow, Precise 
Charge Control (PCC), Smart Inline Technology (SIT) and Digital Valve 
Control (DVC) are trademarks of Gema Switzerland GmbH. 

All other product names are trademarks or registered trademarks of their 
respective holders. 

Reference is made in this manual to different trademarks or registered 
trademarks. Such references do not mean that the manufacturers con-
cerned approve of or are bound in any form by this manual. We have en-
deavored to retain the preferred spelling of the trademarks, and registered 
trademarks of the copyright holders. 

To the best of our knowledge and belief, the information contained in this 
publication was correct and valid on the date of publication. Gema Swit-
zerland GmbH makes no representations or warranties with respect to the 
contents or use of this publication, and reserves the right to revise this 
publication and make changes to its content without prior notice. 

For the latest information about Gema products, visit 
www.gemapowdercoating.com. 

For information regarding patents, visit 
www.gemapowdercoating.com/patents or 
www.gemapowdercoating.us/patents. 

 

Printed in Switzerland 

 

Gema Switzerland GmbH 
Mövenstrasse 17 
9015 St.Gallen 
Switzerland 

Phone: +41-71-313 83 00 
Fax: +41-71-313 83 83 

Email: [email protected] 

 

Summary of Contents for OptiGun GA03-E














































Reviews: