Printed in U.S.A
53
918215/CP0407
Chapter 10
SERVICE AND STORAGE
GENERAL INFORMATION
This chapter contains procedures to follow when
performing routine maintenance checks,
adjustments, and replacements. Many procedures
are also referred to in “Troubleshooting” on
page 65 and in “Maintenance” on page 33. For
engine-related adjustments and servicing
procedures, refer to the engine manual.
WARNING
BEFORE performing any service on the paver,
exercise the MANDATORY SAFETY
SHUTDOWN PROCEDURE on page 15.
After service has been performed, BE SURE to
restore all guards, shields and covers to their
original positions BEFORE resuming paver
operation.
NOTE:
All service routines, except those
described under "Dealer Services," are owner-
operator responsibilities. Refer to “Lubrication”
on page 47 of this manual for lubrication
information.
Precautions
Do not perform any maintenance or repair without
the owner's prior authorization. Allow only trained
personnel to service the paver.
Only Gehl dealers are authorized to perform
warranty repairs. Dealers know the components
covered under the terms of the Gehl Warranty and
the components covered under the terms of vendor
warranties.
IMPORTANT:
Always dispose of waste
lubricating oils, anti-freeze, and hydraulic
fluids according to environmental laws or take
them to a recycling center for disposal. DO
NOT pour them onto the ground or into a
drain.
DEALER SERVICES
The following areas of internal components service
replacement and operating adjustments should only
be performed by (or under the direction of) an
authorized Gehl dealer.
Engine Components
All service procedures related to the internal
components are precise and critical for proper
engine operation. Special training and tools are
required for servicing.
NOTE:
If the engine is not operating properly,
contact your Gehl dealer.
Hydraulic System Components
Valves, pumps, motors and cylinders are
assemblies that require special training and tools
for servicing. All cylinders are designed with
strokes, diameters, checks, and hose connections
specifically for paver application requirements.
Use the hydraulic schematic as a guide for
troubleshooting and service reference. See
“Hydraulic Schematic” on page 51.
Internal service on any of these components should
only be performed by (or under the direction of) an
authorized Gehl dealer.
Electrical Components
Use the electrical schematic when servicing
instrumentation, components, switch connections,
and as a guide for troubleshooting and service
reference. See “Electrical Schematic” on page 50.
Summary of Contents for 1448 Plus
