GE VR11 Reference Manual Download Page 95 | Manualshive

Page: 95 / 118

background image

TMDS / GPIO Connector (P2002)

Table 38: VTM22 TMDS connector

Name

P2002

TXC+/GPIO0 3

TXC-/GPIO1 5

TX0+/GPIO2 7

TX0-/GPIO3 9

TX1+/GPIO4 11

TX1-/GPIO5 13

TX2+/GPIO6 15

TX2-/GPIO7 17

HTPLG/\PEN 24

FUSE_VCC 26

GND

10,12,14,16,18,20,22

NC

1, 2, 4, 6, 8, 19, 21, 23, 25

This connector shares the functions TMDS and GPIO. Only one function is
available at the same time and is board specific.

Serial Interfaces COM1 (P2200, P2100) and COM2 (P2201, P2203)

The VR11 offers two RS232 serial ports. All COM ports are accessible via the
transition module at 10 pole headers and are software selectable for RS-232 or
RS-422/485 operation.

Important note:

COM1 is accessible via an RJ45 type front panel connector (P2200) and via
other connectors at the rear. The front panel connector has only 8 pins. It does
not support the Ring Indicator (RI) on RS232 and it does not support
RS422/485 because it is missing RXD- (negative Receive Data). RS422/485 is
available only on rear connections.

The RS485 output drivers can be enabled or disabled with the DTR signal. An
active DTR means the driver are always enabled. When using RS422 setting
the output drivers are always enabled and the DTR signal is not used. COM1
and COM2 are also available at the rear panel with 9 pole D-sub connectors.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 95

«
...
93
94
95
96
97
...
»

Summary of Contents for VR11























































































































Reviews:

No comments

Related manuals for VR11

NF796M-H310 Series

Brand: JETWAY Pages: 63

Brand: Actel Pages: 2

Brand: Xeltek Pages: 19

Brand: Biostar Pages: 49

Brand: MSI Pages: 36

Brand: NXP Semiconductors Pages: 28

Brand: NXP Semiconductors Pages: 16

Brand: JETWAY Pages: 44

Brand: Bartels Mikrotechnik Pages: 9

Brand: OLIMEX Pages: 17

Brand: ASROCK Pages: 40

GA-N650SLI-DS4L

Brand: Gigabyte Pages: 100

Brand: JETWAY Pages: 46

Brand: Intel Pages: 1

Gamefisher 298.586180

Brand: Gamefisher Pages: 23

Brand: Gigabyte Pages: 116

Brand: Advantech Pages: 136

Brand: ECS Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands