GE VR11 Reference Manual Download Page 24 | Manualshive

Page: 24 / 118

background image

GPIO
8 GPIO in or out (pins shared with DVI-I; GPIO and DVI-I exclude each
other), software configurable

PMC slots
PMC1 with 64 bit/133 MHz PCI-X (3.3 V IO voltage signaling only) and
PMC2 with 32 bit/33 MHz (5 V IO voltage signaling only); PCI mezzanine
connector for standard PMC with front and rear IO. IO signals are available at
the rear connectors.
Compliant to ANSI/VITA 20-2001
PMC2 not available with Front VGA, GigE on front or onboard IDE
Non-Monarch option compliant to ANSI/VITA 32-2003
PMC front I/O not available in style 8

XMC slot
One XMC slot optional in PMC1 location

Important note:

Some PMC2IO signals are shared with the primary IDE signals.
All PMC2IO signals are only available in the configuration with full PMC-IO.
In the partial PMC-IO configuration PMC2IO31 to PMC2IO60, PMC2IO63
and PMC2IO64 are not available.
Make sure that the PMC-IO pins on the PMC module do not conflict with the
IDE signals!

VMEbus
PCI bus to VMEbus controller, up to 60 MByte/s transfer rates
FIFOs for write posting, DMA controller with linked list support
Geographical addressing
VMEbus system controller
Master (including RMW) and Slave (including RETRY*) transfer modes:
BLT, ADOH, RMW, RETRY
A64 / A32 / A24 / A16
D32 / D16 / D8 (SCT, BLT)
D64 (MBLT , 2eVME, 2eSST)

Temperature Sensors
This sensor measures the temperatures of the CPU die and on an onboard
location. The sensors are software readable in 1 °C increments from -55 °C to
+125 °C.

Front panel I/O
2 x GigE, Fast Ethernet, VGA, PMC1 or XMC, PMC2, USB 1-2, Reset, COM1
on RJ45 style connector only for RS232 (without RI),
ST LED for ACPI indication red/amber/green (not with conduction cooled style
8). The other (unnamed) LED location is not used on Vx11 boards
For restrictions or conditions see appropriate chapters in this manual

Rear I/O
Via Transition Module VTM22
DVI-I, VGA, LED, IDE (ATA 100), SATA 1-2,COM1-2, USB 3-4, PMC1 or
XMC, PMC2, Audio, Reset, GPIO [0...7], 2x GigE, ResetO
For restrictions or conditions see appropriate chapters in this manual

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 24

«
...
22
23
24
25
26
...
»

Summary of Contents for VR11























































































































Reviews:

No comments

Related manuals for VR11

Brand: Atmel Pages: 22

Intel P43 Series

Brand: J&W Pages: 37

EZ-USB HX2LP CY4606

Brand: Cypress Pages: 2

Brand: Freescale Semiconductor Pages: 16

Brand: EVGA Pages: 2

Brand: Acorp Pages: 66

Brand: TYAN Pages: 100

Brand: Analog Devices Pages: 13

Brand: Albatron Pages: 46

Brand: ECS Pages: 87

Brand: M-tech Pages: 2

Brand: u-blox Pages: 23

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 129

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 108

Brand: DataExpert Pages: 44

Brand: ASROCK Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands