background image

Critical Power 

 

Modifications reserved 

Page 66/92 

GE_UPS_USM_TLE_SUL_M62_1M0_2US_V010.docx 

User Manual

 TLE Series 625 - 750 - 1000 UL S2

 

 

7.2

 

PROCEDURES SINGLE TLE  Series  625  -  750  -  1000  FUNCTIONING AS 

FREQUENCY CONVERTER 

When the 

TLE Series 625 - 750 - 1000

 functions as a 

Frequency Converter

, the 

Automatic Bypass

 function 

is disabled. 

Therefore the 

Load

 cannot be transferred to 

Utility

 in case of overload, short circuit, or 

Inverter

 failure. 

In situations where the UPS needs to be shut-down for maintenance purposes, also the 

Load

 must be 

shut-down or disconnected. 

 

7.2.1

 

Initial Start-up of the TLE Series 625 - 750 - 1000 as frequency converter 

 

WARNING ! 

Before proceeding to turn on the UPS system, ensure that the AC and DC external 

isolators

 are OFF, and prevent their inadverted operation. 

Ensure that the Output Load distribution  can be powered and all the Output 

Isolators

 are open. 

 

Open the front door and make sure that: 

 

All the 

connections

 to the input/output terminals or bus bars of the UPS have been made correctly. 

 

The 

safety screens

 are fixed in their position. 

 

The switch 

Q1

 

is open 

(Pos. O) and the 

“External Battery Protections”

 

must be open

 (Pos. O). 

 

 

Q1 

UPS Output switch 

 

LEDs on Synoptic Diagram

 

LED 1 

Rectifier 

LED 2

 

Inverter 

LED 3 

Booster/ Battery charger

 

LED 4 

Automatic Bypass 

LED 5 

LOAD on UPS 

 

LED ALARM

 

 

LED LOAD PROTECTED 

 

 

Command Inverter ON 

 

Command Inverter OFF 

 

 

Command 

System shutdown 

 

Command 

System shutdown Reset

 

 

 

 

 

1.  Switch-ON the Utility voltage from the input distribution.

 

The UPS performs a 

“Self-test”

A successful termination of the tests will be indicated with Overall test 

results 

“OK”

Commissioning cannot be continued should one or more tests result 

to be negative. Please contact in this case your 

Service Center

.

 

 

 

 

At this stage the 

Electronic Power Supply

 and 

Control Panel

 are switched 

ON and the 

Buzzer

 sounds. 

Press 

“MUTE”

 key to reset 

Acoustical Alarm

LED ALARM

 remains lit.

 

 

 

Continue

 

 

 

TL

ES_U

L_1

00

0_S1

_Sw

itc

h Q

1_

01

Q1

0 OFF

I ON

Summary of Contents for TLE 625 UL S2





























































































Reviews: