GE TLE 625 UL S2 User Manual Download Page 28

Page: 28 / 92

Critical Power

Modifications reserved

Page 28/92

GE_UPS_USM_TLE_SUL_M62_1M0_2US_V010.docx

User Manual

TLE Series 625 - 750 - 1000 UL S2

LED ALARM (yellow color)

It blinks when one or more alarm is activated. The internal

Buzzer

The

LED

remains blinking (with the alarm condition still present) and the buzzer stops when the key

“MUTE”

is pressed.

The

LED ALARM

is also lighted when the

Load

is not protected by UPS or in case

is open.

LED STOP OPERATION (red color)

It warns about the imminent

Inverter stop

(default parameter = 3 min.) and the consequent

Load

shut-

down as result of:

•

The

battery

is fully discharged and the

Load

cannot be transferred on

Utility

•

Overtemperature or overload condition (>102%) and the

Load

cannot be transferred on

Utility

Bypass

Data regarding

Bypass

See

Section 6.2

Rectifier

Data regarding

Rectifier

See

Section 6.2

Load output

Data regarding

Load

See

Section 6.2

Battery

Data regarding

Battery

See

Section 6.2

Green color: indicates battery charged.

Yellow color: indicates STOP OPERATION status.

Red color:

indicates low battery.

Summary of Contents for TLE 625 UL S2





























































































Search results

Summary of Contents for TLE 625 UL S2

Reviews:

Related manuals for TLE 625 UL S2

Brands by name

Popular brands

GE TLE 625 UL S2, User Manual

Search results

Summary of Contents for TLE 625 UL S2

Reviews:

Related manuals for TLE 625 UL S2

Brands by name

Popular brands