GE SX TRANSISTOR CONTROL IC3645SP4U400N3 Installation And Operation Manual Download Page 20

Page: 20 / 74

DIAGNOSTIC STATUS CODES

SX TRANSISTOR CONTROL

Page 20

January 2000

Section 4.5 Traction Control Codes

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

NONE

Segments do not illuminate on the
Dash Display and/or the Handset.

No input voltage to the control card or the display unit.

MEMORY RECALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Display screen on Dash Display and/or Handset
is blank.

POSSIBLE CAUSE

Positive or negative control voltage is not
present.

•

Insure that the key switch is closed and
voltage is present between P1 & battery
negative (Power Terminal “NEG”). Also check
for voltage between P2 and control negative.

Open circuit between control card AND the Dash
Display or Handset.

•

Check for an open circuit or loose connection
going from the control and the Dash Display or
Handset.

Defective Dash Display or Handset.

•

Replace Dash Display or Handset.

NEG

FU3

KEY

SWITCH

FU5

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-01

No seat switch or deadman switch
input (no voltage to P6).

This status code will be displayed when P6 is less
than 50% battery volts.

MEMORY RECALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Mis-adjusted or defective seat or deadman
switch.

•

Check to see that the seat switch closes
properly.

Open circuit between battery positive and P6.

•

Check for loose connections or broken wires:

−

Between the seat switch and P6

−

Between the key switch and the battery
positive side of the seat switch.

−

Between the seat switch and P2.

•

On vehicles without a seat/deadman switch,
check for a loose connection or broken wire
from P2 and/or P6.

NEG

FU3

KEY

SWITCH

SEAT

FU5

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3











































































Search results

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3

Reviews:

Related manuals for SX TRANSISTOR CONTROL IC3645SP4U400N3

Brands by name

Popular brands

GE SX TRANSISTOR CONTROL IC3645SP4U400N3, Installation And Operation Manual

Search results

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3

Reviews:

Related manuals for SX TRANSISTOR CONTROL IC3645SP4U400N3

Brands by name

Popular brands