GE SX TRANSISTOR CONTROL IC3645SP4U400N3 Installation And Operation Manual Download Page 28

Page: 28 / 74

DIAGNOSTIC STATUS CODES

SX TRANSISTOR CONTROL

Page 28

January 2000

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-27

Control’s power supply is less than 10
Volts DC.

This status code will be displayed when the control’s
power supply is less than 10 volts.

MEMORY RECALL

YES

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Line contactor opens and closes, then can only
be closed by opening and closing the key
switch.

POSSIBLE CAUSE

Discharged Battery

•

Check battery to insure proper state of charge.
Voltage may be dropping below 10 Volts DC
under load.

Loose connection at P1.

•

Insure that the wire connection at P1 is tight.

Defective control.

•

Replace controller unit.

NEG

FU3

KEY

SWITCH

FU5

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-28

Motor field current is too high during
the run mode.

This status code will be displayed when the current
draw in the motor field is sustained above a preset
limit for longer than 70 seconds.

MEMORY RECALL

YES

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Continued operation of vehicle in high motor
current condition.

•

Operate vehicle at lower motor current

condition for 70 seconds.

Function 7 is mis-adjusted to allow higher than
normal motor field current.
Adjust function per OEM instructions.

KEY SWITCH

P17

P2 P6

P12 P8

SEAT

SW.

FOR

. S

EV.

SW.

P10

P18

PY7
PY12
PY10
PY11

FU7

ACCESSORIES

FU6

OSCILLATOR CARD

LEFT CONTROL

FU1

STEER
ANGLE

POT

LINE

POWER

CONNECTIONS

LEFT CONTROL

POS

NEG

FIE

URE

ACC POT

BDI INTERRUPT

FU4

FU2

POWER

CONNECTIONS

RIGHT CONTROL

POS

NEG

FIE

URE

FU5

BRAKE SW.

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3











































































Search results

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3

Reviews:

Related manuals for SX TRANSISTOR CONTROL IC3645SP4U400N3

Brands by name

Popular brands

GE SX TRANSISTOR CONTROL IC3645SP4U400N3, Installation And Operation Manual

Search results

Summary of Contents for SX TRANSISTOR CONTROL IC3645SP4U400N3

Reviews:

Related manuals for SX TRANSISTOR CONTROL IC3645SP4U400N3

Brands by name

Popular brands