background image

SuperBus 2000 2-Amp Power Supply

Installation Instructions

4

Troubleshooting

Trademark/disclaimer

SuperBus is a registered trademark of GE Security. Concord is a trademark of GE 

Security. All other trademarks are property of their owners.

FCC compliance

This device complies with FCC Rules Part 15. Operation is subject to the 

following two conditions.
This device may not cause harmful interference.
This device must accept any interference that may be received, including inter-

ference that may cause undesired operation.
Changes or modifications not expressly approved by GE Security can void the 

user’s authority to operate the equipment.

Specifications

Problem

Action

Green LED is off

1. Check that power supply transformer is 

plugged into outlet.
2. Check that transformer is not plugged into 

an outlet controlled by a switch.
3. Check outlet circuit breaker/fuse. Reset/

replace as needed.

Red LED is off.

Check/correct bus (A & B) wiring connections 

at module and panel.

System touchpads display AUX 

POWER FAIL.

1. Check for shorts on wire connected to 

power 12V OUT terminal.
2. Verify that devices connected to power 

12V OUT terminal are not drawing 

more than 2 amps.

System touchpads display AUX 

POWER BATT trouble.

1. Check that power supply battery is 

connected.
2. Power supply battery needs charging. 

Battery may need at least 4 hours to fully 

charge.

System touchpads display AUX 

AC POWER trouble.

1. Check that power supply transformer is 

plugged into outlet.
2. Check that power supply transformer is 

not plugged into an outlet controlled by a 

switch.
3. Check outlet circuit breaker/fuse. Reset/

replace as needed.

Panel compatibility

Concord 4 series control panels

Power input required

24 VAC, 50 VA class II power transformer

Power output

9 to 14 VDC, 2.0 amps maximum, current 

limited

Battery type

12V, 4.5Ah or 7Ah lead acid

Recommended Battery Manu-

facturer

Portalac Model # PE12V7 (7Ah), PE12V4.5 (4.5 

Ah)

Maximum load for UL installa-

tions

95 mA (4.5Ah battery), 190 mA (7 Ah battery)

Operating temperature

32

°

 to 120

°

 F (0

°

 to 49

°

 C)

Storage temperature

-30

°

 to 140

°

 F (-34

°

 to 60

°

 C)

Max. relative humidity

85%, non-condensing

Dimensions (LxWxD)

5.125 in. x 7.85 in. x 1.0 in. (13 cm x 20 cm x 

2.5 cm) 

UL

985, 1023, and 1610

cUL

C1023-1974, S545-M89

GE Security
1275 Red Fox Road
Arden Hills, MN 55112

Technical Support
T: 800.gesecurity
F: xxx.xxx.xxxx

www.gesecurity.com

                       

   

 

Summary of Contents for SuperBus 2000

Page 1: ...l is 4 000 feet When mounting the power supply in a separate enclosure the power supply mounting location should be determined by the wire runs needed to provide power to devices with minimal loss on the 12V OUT wire Table 1 shows the maximum wire runs between the power supply 12V OUT terminal and the devices it will power For UL installations the 12V OUT is not fully supervised for open circuits ...

Page 2: ...cord 4 in UL systems 1 Unplug the panel AC power transformer and disconnect the backup battery 2 Place the cabinet at the desired location and mark the cabinet mounting holes and knockouts Figure 5 Figure 5 Residential enclosure mounting holes and knockouts 3 Drill holes and insert the appropriate anchors where studs are not present 4 Run wires from all devices to be powered to the power supply 5 ...

Page 3: ...to panel and devices Power Up Use the following procedure for powering up the power supply and panel to verify bus communication 1 Verify that all wiring at the panel and devices are correct 2 Connect the power supply backup battery to the battery terminals on the power supply board Figure 10 Figure 10 Power supply AC and DC power connections 3 Wire the power supply AC transformer to the power sup...

Page 4: ...nal 2 Verify that devices connected to power supply 12V OUT terminal are not drawing more than 2 amps System touchpads display AUX POWER BATT trouble 1 Check that power supply battery is connected 2 Power supply battery needs charging Battery may need at least 4 hours to fully charge System touchpads display AUX AC POWER trouble 1 Check that power supply transformer is plugged into outlet 2 Check ...

Reviews: