manualshive.com logo in svg

GE SecoGear, Installation, Operation And Maintenance Manual

Share
Download
GE SecoGear Installation, Operation And Maintenance Manual Download Page 7

SecoGear – Installation, Operation and Maintenance Manual     7 of 56

Table of Figures (Cont.)

Figure 5-15: Operation Handle Fully Engaged into Switchgear Compartment . . . 39

Figure 5-16: Press Down on the Interlock Pin and Rotate Clockwise to Lock  
the Latch Handle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 5-17: Unlock VCB from Lift Truck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 5-18: Lock VCB into Switchgear   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 5-19: Rotate Interlock Pin Counterclockwise to Unlock the Latch Handle   40

Figure 5-20: Interlock Latch Handle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 5-21: Stop in Proper Position  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 5-22: Eliminating Stop Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 5-23: Release Floor Lock   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Figure 5-24: Release Secondary Plug from VCB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 5-25: Insert Secondary Plug and Lock into Switchgear  
Compartment Socket  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Figure 5-26: Racking Handle   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 5-27: Racking Handle Insertion on Door  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 5-28: Access Hole Open  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 5-29: Disconnected/Test Position (Green) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 5-30: Intermediate Position (Yellow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 5-31: Connected Position (Red) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Figure 6-1: SecoVac Test Box  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Figure 9-1: Rear Compartment Assembly Illustration  . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 9-2: CTs mounted in compartment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 9-3: CT Spacers, 7/8” (left) and 2” (right)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 9-4: CT Spacers Installed  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 9-5: CT Wire Harness in Compartment   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 9-6: CT Wires Connected  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Figure 9-7: CT Installed, Shutters in Open Position  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Figure 9-8: SecoGear Manual Racking Port Padlocked. . . . . . . . . . . . . . . . . . . . . . . . . . 50

Figure 9-9: Compartment Door Padlock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 9-10: Shutter Padlock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 9-11: Kirk Lock Location in SecoGear  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 9-12: Initial Stopper Rod Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Figure 9-13: Locked Stopper Rod Position  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Summary of Contents for SecoGear

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands