PACSystems* RX3i
IC695PNC001-AJ
GFK-2573K
PROFINET Controller Module
February 2015
PNC001
IP ADDRESS
INTERFACE MAC
PORTS
FRONT
TO INSTALL, TORQUE TO
6 IN-LB. TO UNINSTALL,
REVERSE MOTION
3 4
1 2
1
2
3
4
OK
LAN
STATUS
CONFIG
ACTIVE
USB
USB
RESTART
!
The PACSystems
RX3i PROFINET Controller (PNC) module, IC695PNC001, connects a
PACSystems RX3i controller to a high-speed PROFINET local area network. It enables the RX3i
controller to communicate with I/O-Devices on the LAN. The PNC provides all the functions,
services, and protocols required for certification as a PROFINET I/O Version 2.2 I/O Controller,
running at both 100 Mbps and 1 Gbps.
The PNC supports 10/100/1000 Mbps Copper, 100/1000 Mbps Multi-mode Fiber, and
100/1000 Mbps Single-mode Fiber. The LAN can include media interfaces of more than one
type. PROFINET communications on the LAN require 100 and 1000 Mbps link speed. 10 Mbps
cannot be used for PROFINET communications. However, 10 Mbps can be used for other
types of Ethernet traffic such as ping and telnet.
Features of the RX3i PNC include:
▪
Full programming and configuration services for the PROFINET Controller, VersaMax
PROFINET Scanner and third-party I/O-Devices using Proficy* Machine Edition.
▪
Firmware upgrades using the WinLoader software utility.
▪
Built-in Command Line Interface function that provides direct monitoring and partial
configuration via the micro USB port or using telnet.
Note:
The USB port is for system setup and diagnostics only. It is not intended for
permanent connection.
▪
Support for star, ring, and daisy-chain/line network topologies.
▪
Four switched Ethernet ports - two 8-conductor RJ-45 shielded twisted pair
10/100/1000 Mbps copper interfaces and two Small Form-factor Pluggable (SFP) cages
for user-supplied SFP devices.
▪
Internal clock synchronized with the RX3i CPU for time-stamped diagnostics entries.
▪
Restart pushbutton to manually restart the PNC without power cycling the system.
▪
LEDs: OK, LAN, STATUS, CONFIG, ACTIVE, USB, and four Port LEDs.
▪
Compliant with EU RoHS Directive using the following exemptions identified in the
Annex: 7c-I and 7c-III.
Ordering Information
IC695PNC001
PACSystems RX3i PROFINET Controller Module 10/100/1000, 4 Ports - 2 SFP connections, 2 Copper
IC200PNS001
VersaMax PROFINET Scanner, 10/100, 2 Ports, Copper
IC200PNS002
VersaMax PROFINET Scanner, 10/100, 2 Ports, Multimode Fiber
IC695PNS001
PACSystems RX3i PROFINET Scanner Module 10/100/1000 with four Ports (two SFP connections, two
Copper) - Includes a blank SD card, two mounting screws and a USB port cover
IC695SPC100
RX3i 10/100/1000base-TX (CAT5 100m) SFP
IC695SPF002
RX3i 100Base-FX (fiber 2 km) SFP
IC695SPF550
RX3i 1000Base-SX (fiber 550 m) SFP (MMF)
IC695SPF010
RX3i 1000Base-LX (fiber 10 km) SFP (Single mode fiber - SMF)
© 2015 General Electric Company. All Rights Reserved.
*
Indicates a trademark of General Electric Company and/or its subsidiaries. All other trademarks are the property of their respective
owners.