manualshive.com logo in svg

GE Profile Advantium SCA2001KSS, Installation Instructions Manual

Share
Download
GE Profile Advantium SCA2001KSS Installation Instructions Manual Download Page 21

21

Installation Instructions

MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL SAFETY,
WE RECOMMEND THAT

TWO PEOPLE INSTALL

THIS OVEN. 

IMPORTANT: Do not grip or use handle during
installation.

NOTE: 

If your cabinet is metal, use the nylon grommet

around the power cord hole to prevent cutting of the cord.

NOTE:

We recommend using filler blocks if the cabinet

front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used, case damage
may occur from over tightening screws.

C4

Secure blower unit to oven with the screw removed 
in Step 2.

Replace blower plate with the screws removed 
in Step 1.

7

6

Blower Motor
Screw

NOTE:

When mounting the oven, 

thread power cord through hole 
in bottom of top cabinet. Keep it 
tight throughout Steps 1–3. 
Do not pinch cord or lift oven 
by pulling cord.

Rotate front of oven up 
against cabinet bottom.

Insert a self-aligning screw through top center cabinet
hole. Temporarily secure the oven by turning the
screw at least 

two full turns 

after the threads have

engaged

. 

(It will be completely tightened later.) 

Be sure to keep power cord tight. Be careful not to
pinch the cord, especially when mounting flush to
bottom of cabinet.

If your cabinet front hangs more than 2

3

⁄

4

″

below the

cabinet bottom, you may need to use longer screws than
the ones provided with this product. The screws provided
with this product (hardware item 3) are self-aligning, 
large-head machine screws 1/4

″

diameter, 3

1

⁄

4

″

long, 

with SAE 28 threads per inch. It is important that you 
use replacement screws just long enough to attach the
product to the cabinet. The length can be determined 
by measuring the height of the overhang from the top 
of the cabinet floor to the bottom of the overhang and
adding 1

″

to that length. This will be the length of the

1/4

″

SAE 28 threads per inch screws you need.

You will also need to use washers 3/4

″

diameter to fit the

screws you purchase. This will prevent the screw heads
from pulling through the bottom of the cabinet when
tightening during installation.

3

2

Lift oven, tilt it
forward, and 
hook slots at back
bottom edge onto
2 lower tabs of
mounting plate.

1

Retaining
Flange

Blower Plate

Back of Oven

Blower Plate Screws

Summary of Contents for Profile Advantium SCA2001KSS

























Reviews:

No comments

Brands by name

Popular brands

Load more brands