manualshive.com logo in svg

GE Profile Advantium SCA2001KSS, Installation Instructions Manual

Share
Download
GE Profile Advantium SCA2001KSS Installation Instructions Manual Download Page 14

14

ADJUST THE EXHAUST
ADAPTOR

Open the top cabinet and adjust the exhaust adaptor to
connect to the house duct.

For top exhaust on the flat-bottomed cabinets, open the
top cabinet and attach the exhaust adaptor to the oven
through the cabinet bottom with the 2 bronze metal
screws provided.

A5

Back of Oven

Damper

Installation Instructions

MOUNT THE OVEN 

(cont.)

If your cabinet front hangs more than 2

3

⁄

4

″

below the

cabinet bottom, you may need to use longer screws than
the ones provided with this product. The screws provided
with this product (hardware item 3) are self-aligning, 
large-head machine screws 1/4

″

diameter, 3

1

⁄

4

″

long, 

with SAE 28 threads per inch. It is important that you 
use replacement screws just long enough to attach the
product to the cabinet. The length can be determined 
by measuring the height of the overhang from the top 
of the cabinet floor to the bottom of the overhang and
adding 1

″

to that length. This will be the length of the

1/4

″

SAE 28 threads per inch screws you need.

You will also need to use washers 3/4

″

diameter to fit the

screws you purchase. This will prevent the screw heads
from pulling through the bottom of the cabinet when
tightening during installation.

Attach the oven to the top cabinet.

Insert 2 self-aligning screws through outer top cabinet
holes. Turn two full turns on each screw.

Tighten the outer 2 screws to the top of the oven.
(While tightening screws, hold the oven in place
against the wall and the top cabinet.)

7

5

4

A4

CONNECTING DUCTWORK

Extend the house duct down to connect to the
exhaust adaptor.

Seal exhaust duct joints using duct tape.

2

1

A6

House Duct

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Oven Top

Equivalent 
to Depth 
of Cabinet
Recess

Self-Aligning Screw

Install grease filters. 
See the Owner’s Manual
packed with the oven.
Remove the tape from the
cooktop lamp covers on 
the bottom of the oven.

Secure the power cord to the cabinet wall, as desired
to keep excess length out of the way using the power
cord strap and the black metal screw.

9

8

Tighten center
screw completely.

6

Summary of Contents for Profile Advantium SCA2001KSS

























Reviews:

No comments

Brands by name

Popular brands

Load more brands