GE NX-148E - Security NetworX LCD Keypad User Manual Download Page 7

Page: 7 / 30

NX-148E LCD Keypad

III.

KEYPAD FUNCTIONS

ARMING YOUR SYSTEM IN THE “AWAY” MODE

AWAY is utilized when the user is going away from the premise and wants the interior
protected. Listed below are the steps to arm in the AWAY Mode:

Step 1

Close all protected doors and windows.

Ready light

will be on or flashing

when all protected zones and
sensors are secure.

NOTE: If

any zones are bypassed, a
sensor in that zone can be
violated without affecting the

ready light

The security system will not
arm if the

ready light

is off.

Refer to "Making Your System
Ready to Arm".

If the

power light

is off, you

have no AC power. Restore power if possible. If not, contact the
installing company.

Step 2

Enter your 4 or 6 digit user code to arm the system.

The

armed and exit lights

will illuminate.

You may now leave the building.

IMPORTANT!

The

exit light

will flash rapidly for the last 10 seconds of the exit delay as a warning

to the user that the exit time is about to expire. The user may wish to disarm and
rearm the system if more time is needed.

MAKING YOUR SYSTEM READY TO ARM

If the

ready light

is not on or if it is flashing, a zone is not secure. To identify this zone,

use the scroll keys

•

–

to the right of the display to browse through the zones

that are not normal. If you wish to bypass or unbypass one of these zones, press the
[

BYPASS

] key while that zone is being displayed. When finished viewing the zones,

press the

key to return to the code entry screen.

System Ready

Type Code to Arm

System Not Ready

For help, press

System Armed

All Zones Secure

Summary of Contents for NX-148E - Security NetworX LCD Keypad































Search results

Summary of Contents for NX-148E - Security NetworX LCD Keypad

Reviews:

Related manuals for NX-148E - Security NetworX LCD Keypad

Brands by name

Popular brands

GE NX-148E - Security NetworX LCD Keypad, User Manual

Search results

Summary of Contents for NX-148E - Security NetworX LCD Keypad

Reviews:

Related manuals for NX-148E - Security NetworX LCD Keypad

Brands by name

Popular brands